Pwm dc 6v

This DC Motor Speed Controller allows controlling the direction of a DC motor using a Pulse-Width-Modulated (PWM) DC voltage with a Duty Cycle fully adjustable from 0%-100%. The motor speed controller can easily provide a continuous current of3A to your DC motor or other DC load. Main technical parameters: Input supply voltage:6V-28VDC The maximum output power: 80W The maximum continuous output current:3A Duty Cycle adjustable:0%-100% Operating instruction: 1. Connect your DC motor (or DC load) to the motor terminals as indicated on the wiring diagram. 2. Connect a voltage of 10V-36V DC to the circuit making sure of the correct polarity of the connection. Note that the voltage applied to the motor will be supply voltage applied to the circuit. It is recommended to add an appropriately rated fuse inline with the positive supply in order to protect the circuit from any possible short circuits. 3. You can now control the speed of the motor through potentiometer. Views: 4

DC Motor Speed Control Switch 13KHz 12V-40V 10A Pulse Width Modulation PWM now in Faisalabad Brand new and high quality. Control the speed of a DC motor with this controller. High efficiency, high torque, low heat generating. With reverse polarity protection, high current protection. Brand new and high quality. Control the speed of a DC motor with this controller. High efficiency, high torque, low heat generating. With reverse polarity protection, high current protection. Package Include: 1 x DC Motor Speed Control Switch Working Voltage: DC 12V – DC 40V Control Power:0.01 – 400W. Static Current:0.02 A (Standby). PWM Duty Cycle:10% -100%. PWM Frequency:13 KHz. Material: Plastic, metal. Size:6cm x 5.5cm x 2.8cm Views: 3

Specifications: Operating voltage: DC12V circuit load capacity: maximum current output per 5A, current up to bus 9A output range: first channel 20% -100%, or 40% -100% (TFL = ON) second channel and second Three channels 10% -100% (Note: The above range only the PWM range, the fan varies depending on the actual control effect.) Temperature probe parameters: 50k B = 3950 thermostat temperature zone error: probe depending on error temperature, Generally 3-5% stall alarm minimum speed: 700-800 rpm function setting switch Description: TFL (No. 1): minimum temperature channel PWM setting, when the state FAN1 PWM minimum 40%, OFF minimum PWM FAN1 is 20%. TP1 TP2 (No.2, 3): Temperature channel control temperature zone should be interpreted as follows in use temperature probe): TP1 TP2 acceleration temperature full speed temperature off 35 ° C 45 ° C off 40 ° C 55 ° C Off 50 ° C 70 ° C 60 ° C A temperature lower than 90 ° C Accelerated temperature, minimum rotation speed at the output; more than all temperature, always full speed at the output. BF1 BF2 (No. 4, 5): Supported FAN1 FAN2 Stall alarm function switch, open channel fan disassembled when supported, controller soundand and light (operate with the puzzle), automatically excluded fan rotation recovered. BF1 and BF2 both open (ON), FAN1, FAN2 or one or both stop, the controller is alarm! Package included: 1x speed controller 1x temperature probe Magnetic buzzer Views: 5

Specifications: – Size: Approx. 96 x 61 x 34mm/3.78 x 2.40 x 1.34” – Input Voltage Range: DC6V-60V – Output Voltage: Linear with load – Output Current: 0A-30A – Continuous Current: 20A – Speed Range: 0% to 100% – Regulation Method: Potentiometer – Regulation Type: Regulating Current – Control Frequency: 15KHz – Wiring Type: Screw terminal Features: – Speed controller is made with high quality circuit board which ensures a longer service life. – This simple and easy-to-use DC motor speed controller has an stable performance. – Designed with a digital display that shows the rate in percentage of actual speed to maximum speed. – This motor speed controller uses screw terminals for convenient and quick wiring. – Comes with a momentary start/stop switch and a speed control potentiometer. Package Included: – 1 x Speed Controller Like our Page Electronics Panga Views: 2

Specifications: Input Voltage: DC6V-60V Output Voltage: Linear with load(voltage drop at motor 2 terminals) Output Current: 0A-30A Continuous Current: Views: 1

Price: Seller Type: An Individual Condition: Used Feature: The most important feature of this solar charge controller is simple PWM design, low cost, heavy duty microcontroller based design, available BOOST / trickle charging to control the voltage & current according to batteries: a)    Solar Charger Micro-controller intelligent Fully automatic system b)   Day/Night switch for Street light OR Auto ON/OFF system in day (means LOAD OFF in a full day due to sun light power detector system) or night (means LOAD ON in a full Night or sun light power not available in this time). c)    Flout & Boost charging option d)    BOOST Flout: Charging option 14.2 for boost & Flout for % full battery charging. e)    LBCO Low Battery Cut OFF; disconnect the load when battery potential low. f)     Low Battery protection: Low battery cut-off for safe to load 10.5VDC for 12V battery. g)    Reverse diode protection. h)    Charging indicator show the battery charging & battery potential gradually increases. i)     When Solar connect in a day or sun rise SOLAR ON indicator glow. Means sufficient power available for battery charging. j)     Available from single battery 12VDC to 32-Battery bank system 384VDC, with all full options. k)    Compact Design fits Your Working Environment Open circuit voltages as compare to desire charging for a Battery 12V max open circuit voltages = 19VDC/20VDC Applications: This solar charger suitable for following types of solar applications: a)    Street Light. b)   Solar home light/ garden light. c)    Battery Charging from the P.V Solar module. d)    Low Battery protection, may be used for sensitive equipment like medical, I.T related computer base systems & etc… Indicator: (Picture 1) start from left to right. Day/Night mode means select a street light auto on/off function, when solar panels generate the power means sun light available then load automatically off. When sun light not available or solar panels not generating the power the load/street light automatically on. Load indicator, bright indicate there is output, Load could work, “off” indicate there is not output, and Load can not work. This is normal phenomenon. When the battery voltage recovers to 12.6V or (25.2v), the Load will be automatically working, at this time the indicator is off. 3. Charger Indicator cct, red; bright indicate the voltage of the battery is require to charge OR Charger circuit ready to charge the battery in solar available. Charging Indicator, green, bright indicate the battery need to charge OR on charging, flickering means float charging, off means charge has stop. Solar indicator means solar energy available. Available at Karachi Pakistan pls call or visit at ARDL (Anosha Research & Development electronics Lab): Lab-2 LS-43 Bolck-15 Dastagir Society Karachi-, ,

Specification: Brand: new Material: Nylon + Plastic + Metal Color: Black (As the pictures shown) Length(approx.): 39.5cm/15.55in Item Type: 5-Port Fan Hub Connector A: 1 – TX4 4-pin Female Connector B: 1 – TX4 4-pin Male for CPU fan (including Detect tach pin) Voltage: DC 12V It is designed for enthusiasts with need for controlling numerous system fans. Capable of expanding one motherboard PWM fan header to support up to five fans. Support PWM function, speed control, satisfy your control needs. Compatible with 3-pin / 4-pin fans (Due to 3 pins no PWM controller, 3-pin fans would run in full speed.) Support cable management. Comes with self-stick for easy installation and options to hide the PCB itself. Since only one RPM signal can be read by one motherboard connector, only CPU Fan channel of the PWM splitter carries an RPM signal; Thus the motherboard will only read the RPM signal of the PWM device that is connected to channel 1 of the splitter. Like our page Electronics Panga Views: 2

1. operating voltage: DC 5V-36V; 2. The trigger source: digital high-low (DC3.3V-20V), can be connected microcontroller IO port, PLC interfaces, DC power, you can access the PWM signal, the signal can be supported frequency range 0–20KHZ. 3. Output capacity: DC 5V-36V, at room temperature, DC 15A, power 400W! 4. Application: High power equipment, motors, bulbs, LED lights, DC motors, micro-pumps, solenoid valve; control the speed of the motor, lamp brightness. 5. life: unlimited-off; 6. Operating temperature: -40-85 °; 7. Size: 3.4 * 1.7 * 1.2cm Views: 3

Introduction H801WiFi communicates with Android cell phone via WiFi to achieve the adjustment function. Router can be set as an access point, you can connect the phone and H801WiFi to the same router. once phone and H801WiFi are connected to the router, you can also set H801WiFi as a wireless access point so that another H801WiFi can connect to it, this way, multiple H801WiFi can be connected wirelessly to extend the distance control and increase the number of the controller. 2. Features (1). Connect and control lamps easily by LED Dimmer. (2). RGBWW output, 5 PWM data paths, each route max 4A. (3). Update frequency is 500HZ. (4). Support 802.11 b / g / n. (5). Fast transmission, the sensitive response. (6). H801WiFi can be controlled separately. (7). More phones can control H801WiFi at the same time. (8). Built-in dozens of effects. 3. Specifications Input voltage: DC5 ~ 24V Consumption: 0.5 W dimensions: 93mm x 46mm x 20mm like our page Electronics Panga Views: 2

Price: Seller Type: An Individual Condition: New Product Details Specifications: Receiver Specifications: Receiving Frequency: Ghz Intermediate Frequency: 480Mhz Video OUT Power Source: 9V Dimension: 120x81x20mm Receiving Sensitivity: 48dB Horizontal Definition: 380 Lines Angular Field of View: 38 deg Operation Temperature: 5~ 35 deg C Transmission Frequency: 1.2Ghz Synchronization System: Internal Backlight Compensation: Auto Locked Frequencies Recommended Max Range for Objects: 7~8 Meters Transmission Range: 20 Meters Power Adapter: DC 6V Dimension: 20x20x22mm Approved: CE / FCC Accessories: AV-out Cable Antenna Camera's Adapter Receiver's AC / DC Adapter

ePower 2.4GHz Wireless Surveillance Camera Kit w/4-Channel Wireless Receiver & Wireless Color Camera w/Microphone (Gray) Condition New Unit Dimensions Are 7.75x7.25x3.5 inches 19.7x18.4x8.9 cm The Warranty Period Is 00 Days Each Unit Weighs 2.60 lbs / 1.18 kg Packaging Retail Box Each Master Box Has 10 Units Product Number CCTV-E-POWER Master Box Dims Are 19x16x8.25 inches 48.3x40.6x21.0 cm Tech Support By Dealer Each Master Box Weighs 28 lbs / 12.70 kg Support Contact -- Each Pallet Has 300 Units Regulatory Approval FCC, CE Each Pallet Weighs 830 lbs / 376.49 kg Country of Origin Taiwan Keep at eye on your home or business with the ePower CCTV-E-POWER Wireless Surveillance Camera Kit! With the CCTV-E-POWER, there's no need for messy wires to deal with! It comes with a wireless color camera, wireless receiver and a remote control. The receiver connects to a TV, DVR or VCR via its composite AV jacks (AV cable included). Operating at 2.4 GHz frequency, this wireless kit can transmit and receive video and audio through walls and has an indoor range of up to 164-feet (50 meters) and a maximum outdoor range of up to 656-feet (200 meters)! It's also ideal for monitoring your baby's room or any room in the house as well as the outside your home! Features/Specifications: ePower 2.4 GHz Wireless Surveillance Camera Kit General Features: Includes a wireless color camera, wireless receiver and a remote control Transmits and receives video and audio through walls Auto switching Adjustable dwell time from 0 to 10 seconds IR remote control included for channel selection and deletion Outdoor maximum distance of up to 200 meters Built-in adjustable antenna for both camera and receiver Camera Features: Weather-proof Channels: 4 Built-in Transmitter Scanning System: 2:1 interface Effective Pixels NTSC: 510 (H) x 492 (V) Resolution: 380 TV lines Synchronization: Internal Minimum Illumination: 3 Lux Video output: 1 V(p-p) / 75O Frequency: 2400 MHz- 2483 MHz Transmitting power: 0 dBm (FCC), 10 dBm (CE) Modulation type: FM Frequency stability: ± 100 KHz Power consumption: DC 6V Current consumption: 150 mA Dimensions: 1.3 x 1.75 x 3.4-inches (H x W x D, approximate) Receiver Features: Channels: 4 Demodulation type: FM Sensitivity: - 90 dBm Frequency stability: ± 100 KHz Power consumption: DC 9V Current consumption: 200 mA Connectors: Composite video and L/R audio Dimensions: 1 x 4.4 x 2.8-inches (H x W x D, approximate) Operating Range: Indoors: 30 m - 50 m Outdoors: 150 m - 200 m Regulatory Approvals: FCC CE Package Includes: Wireless Color Camera Wireless Receiver AV cable Remote control Manual Camera mounting bracket Camera AC adapter (Input: 120V AC, 60Hz, Output: 6 VDC, 500 mA) Receiver AC adapter (Input: 120V AC, 60Hz, 7.5W, Output: 9 VDC, 500 mA) Additional Information: Notes: Model: CCTV-E-POWER Product Requirements: Available power outlet(s)

Facebook.com/SmartGadgetPk Product Details Specifications: Receiver Specifications: Receiving Frequency: Ghz Intermediate Frequency: 480Mhz Video OUT Power Source: 9V Dimension: 120x81x20mm Receiving Sensitivity: 48dB Horizontal Definition: 380 Lines Angular Field of View: 38 deg Operation Temperature: 5~ 35 deg C Transmission Frequency: 1.2Ghz Synchronization System: Internal Backlight Compensation: Auto Locked Frequencies Recommended Max Range for Objects: 7~8 Meters Transmission Range: 20 Meters Power Adapter: DC 6V Dimension: 20x20x22mm Approved: CE / FCC Accessories: AV-out Cable Antenna Camera's Adapter Receiver's AC / DC Adapter Box Pack - No Warranty

Product Details Specifications: Receiver Specifications: Receiving Frequency: Ghz Intermediate Frequency: 480Mhz Video OUT Power Source: 9V Dimension: 120x81x20mm Receiving Sensitivity: 48dB Horizontal Definition: 380 Lines Angular Field of View: 38 deg Operation Temperature: 5~ 35 deg C Transmission Frequency: 1.2Ghz Synchronization System: Internal Backlight Compensation: Auto Locked Frequencies Recommended Max Range for Objects: 7~8 Meters Transmission Range: 20 Meters Power Adapter: DC 6V Dimension: 20x20x22mm Approved: CE / FCC Accessories: AV-out Cable Antenna Camera's Adapter Receiver's AC / DC Adapter Box Pack - No Warranty

Bluetooth 5.0 Large Color LCD Screen Handsfree Mic Call & Recording Supply: DC 5V 12V/DC 6V 12V Built-in 2 * 25W Amplifier Size: 92*41MM

Mini Stitch Portable Handy Sewing Machine in Pakistan Description Hand-Held Sewing Machine The Hand-Held Sewing Machine is a small, handy, lightweight, easy to carry around piece. Now you can sew, mend, and work on other small projects with ease without dragging out your bulky sewing machine, it is great for students and handy while travelling. Features Lightweight and compact Easy to use Sews most fabrics Specifications Dimensions L x W x H 21cm x 3.5cm x 7cm Power 4 x AA 1.5V Batteries not included or power adaptor DC 6V 600mA not included Package Includes 1 x Hand-Held Sewing Machine 1 x Needle Thearder 2 x Extra Needles 1 x Spindle 3 x Extra Bobbins With Therad.