Dc 5a pwm motor

Specifications: Operating voltage: DC12V circuit load capacity: maximum current output per 5A, current up to bus 9A output range: first channel 20% -100%, or 40% -100% (TFL = ON) second channel and second Three channels 10% -100% (Note: The above range only the PWM range, the fan varies depending on the actual control effect.) Temperature probe parameters: 50k B = 3950 thermostat temperature zone error: probe depending on error temperature, Generally 3-5% stall alarm minimum speed: 700-800 rpm function setting switch Description: TFL (No. 1): minimum temperature channel PWM setting, when the state FAN1 PWM minimum 40%, OFF minimum PWM FAN1 is 20%. TP1 TP2 (No.2, 3): Temperature channel control temperature zone should be interpreted as follows in use temperature probe): TP1 TP2 acceleration temperature full speed temperature off 35 ° C 45 ° C off 40 ° C 55 ° C Off 50 ° C 70 ° C 60 ° C A temperature lower than 90 ° C Accelerated temperature, minimum rotation speed at the output; more than all temperature, always full speed at the output. BF1 BF2 (No. 4, 5): Supported FAN1 FAN2 Stall alarm function switch, open channel fan disassembled when supported, controller soundand and light (operate with the puzzle), automatically excluded fan rotation recovered. BF1 and BF2 both open (ON), FAN1, FAN2 or one or both stop, the controller is alarm! Package included: 1x speed controller 1x temperature probe Magnetic buzzer Views: 5

Specifications: Input Voltage: DC6V-60V Output Voltage: Linear with load(voltage drop at motor 2 terminals) Output Current: 0A-30A Continuous Current: Views: 1

DC Motor Speed Control Switch 13KHz 12V-40V 10A Pulse Width Modulation PWM now in Faisalabad Brand new and high quality. Control the speed of a DC motor with this controller. High efficiency, high torque, low heat generating. With reverse polarity protection, high current protection. Brand new and high quality. Control the speed of a DC motor with this controller. High efficiency, high torque, low heat generating. With reverse polarity protection, high current protection. Package Include: 1 x DC Motor Speed Control Switch Working Voltage: DC 12V – DC 40V Control Power:0.01 – 400W. Static Current:0.02 A (Standby). PWM Duty Cycle:10% -100%. PWM Frequency:13 KHz. Material: Plastic, metal. Size:6cm x 5.5cm x 2.8cm Views: 3

This DC Motor Speed Controller allows controlling the direction of a DC motor using a Pulse-Width-Modulated (PWM) DC voltage with a Duty Cycle fully adjustable from 0%-100%. The motor speed controller can easily provide a continuous current of3A to your DC motor or other DC load. Main technical parameters: Input supply voltage:6V-28VDC The maximum output power: 80W The maximum continuous output current:3A Duty Cycle adjustable:0%-100% Operating instruction: 1. Connect your DC motor (or DC load) to the motor terminals as indicated on the wiring diagram. 2. Connect a voltage of 10V-36V DC to the circuit making sure of the correct polarity of the connection. Note that the voltage applied to the motor will be supply voltage applied to the circuit. It is recommended to add an appropriately rated fuse inline with the positive supply in order to protect the circuit from any possible short circuits. 3. You can now control the speed of the motor through potentiometer. Views: 4

Specifications: – Size: Approx. 96 x 61 x 34mm/3.78 x 2.40 x 1.34” – Input Voltage Range: DC6V-60V – Output Voltage: Linear with load – Output Current: 0A-30A – Continuous Current: 20A – Speed Range: 0% to 100% – Regulation Method: Potentiometer – Regulation Type: Regulating Current – Control Frequency: 15KHz – Wiring Type: Screw terminal Features: – Speed controller is made with high quality circuit board which ensures a longer service life. – This simple and easy-to-use DC motor speed controller has an stable performance. – Designed with a digital display that shows the rate in percentage of actual speed to maximum speed. – This motor speed controller uses screw terminals for convenient and quick wiring. – Comes with a momentary start/stop switch and a speed control potentiometer. Package Included: – 1 x Speed Controller Like our Page Electronics Panga Views: 2

Product Description It contains two L293D motor drivers and one 74HC595 shift register. The shift register expands 3 pins of the Arduino to 8 pins to control the direction for the motor drivers. The output enable of the L293D is directly connected to PWM outputs of the Arduino. Can drive 4 DC motors or 2 stepper motors or 2 Servo Up to 4 bi-directional DC motors with individual 8-bit speed selection Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping. 4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 36V DC Pull down resistors keep motors disabled during power-up reset button 2 external terminal power interface, for seperate logic/motor supplies Tested compatible for Mega, Diecimila & Duemilanove

1. operating voltage: DC 5V-36V; 2. The trigger source: digital high-low (DC3.3V-20V), can be connected microcontroller IO port, PLC interfaces, DC power, you can access the PWM signal, the signal can be supported frequency range 0–20KHZ. 3. Output capacity: DC 5V-36V, at room temperature, DC 15A, power 400W! 4. Application: High power equipment, motors, bulbs, LED lights, DC motors, micro-pumps, solenoid valve; control the speed of the motor, lamp brightness. 5. life: unlimited-off; 6. Operating temperature: -40-85 °; 7. Size: 3.4 * 1.7 * 1.2cm Views: 3

Features: This is a high-quality, high-power, cost-effective Motor Driver High current 4.5A, high voltage 45V, output short circuit protection, superior performance! automatic half current function. And a semi-automatic flow switch, easy to use. the use of high-speed optical coupling 6N137 ensure high-speed without losing step. Used to increase the heat sink, good heat dissipation. Using common anode input mode, there are two input terminals, wiring more convenient. For 4.2A 42,57,86 within the two-phase / four-phase / four-wire / six-wire stepper motor. Automatic half current function. Low-pressure shut-off, overheating parking and over-current protection circuit, short-circuit protection Specifications: Type: TB6600 Operating voltage DC 10V-45V. DC32V Size: 8 x 5 x 3.5cm Net Weight: 118.3g Package includes: 1 x Motor Driver Views: 2

Features: Working voltage DC 10V-35V. Recommended using a switching power supply DC24V power supply. 6N137 high-speed optical coupling, guarantee high speed without losing the step. Using the TB6560AHQ chip with low voltage shutdown, overheating stop and over current protection circuit to ensure optimal performance. Rated maximum output: ± 3A, peak 3.5A. For two-phase within 42,57 stepping 3A / four-phase / of line four / six-wire stepper motor, and is not suitable for more than 3A stepper motor. Automatic half current function. Subdivision: whole step, half-step, step 1/8, 1/16 step, a maximum of 16 subdivisions. Specifications: Working voltage: DC 10-35V Rated maximum output: ± 3A, peak 3.5A. Main colour: Green Size:75 x 50 x 33mm Net weight: 83g Package content: 1x TB6560 3A driver board Working voltage: DC 10-35V Rated maximum output: ± 3A, peak 3.5A. Main color: Green Size:75 x 50 x 33mm Net weight:83g Package content: 1x TB6560 3A driver board Views: 1