Motor driver expansion board

L293D Motor DriverThis L293D motor driver is a 4-channel driver with an Arduino shield form factor. This is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepper motors. It lets you drive 2 Stepper motor or 4 DC motors with an Arduino, controlling the speed and direction of each one independently.Features:2 interface for 5V Servo Can drive 4 DC motors or 2 stepper motors or 2 Servo Up to 4 bi-directional DC motors with individual 8-bit speed selection Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping. 4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 36V DC Pull down resistors keep motors disabled during power-up Reset button 2 external terminal power interface, for separate logic/motor supplies

Features: Double H bridge drive Chip L298N (ST NEW) Logical voltage 5V Drive voltage 5V-35V Logic current 0mA-36mA Drive current 2A(MAX single bridge) Storage temperature -20 to +135 Max power 25W Weight 30g Small size mm (approx 1.75"" x 1.75"" x 1"") Compatible with L297/L298 driver Note This module has a built-in 5v power supply for external use. Drive voltage is 7v-35v. DO NOT input voltage to +5v supply interface - this is OUTPUT only." Box Pack - No Warranty

Features Double H bridge drive Chip L298N ST NEW Logical voltage 5V Drive voltage 5V-35V Logic current 0mA-36mA Drive current 2AMAX single bridge Storage temperature -20 to 135 Max power 25W Weight 30g Small size 434327mm approx 1.75 x 1.75 x 1 Compatible with L297L298 driver Note This module has a built-in 5v power supply for external use. Drive voltage is 7v-35v. DO NOT input voltage to 5v supply interface - this is OUTPUT only.

Toshiba TBAHQ chip - High power, maximum 3.5A drive current. · Professional design, two-stage signal processing, super anti-jamming. · microstep setting - Higher accuracy. · Adjustable drive current settings for each axis - % of full current can be set for different stepper motors. · Overload, over-current and over-temperature safety - Full protection for your computer and peripheral equipment. · On board current switching - Power output can be set according to specific user requirement. · Relay spindle interface - Outputs Max. 36V 7.5A for spindle motors or coolant pump (only one device can be powered by this output!) · 4 channel inputs interface- Can be used for XYZ limit and emergency stop. · Bipolar constant current chopper drive with non-resonant region. · Full closed-type optical isolation to protect the user's computer and equipment · Four control inputs (divided into pairs of knives) - Allows setting of limit and emergency stop. · Universal architecture - Supports most parallel software MACH3,KCAM4,EMC2 etc.

L298 Motor Driver Controller Board The L298N driver module, using ST L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface , you can chip circuitry to 5V power supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential. Stepper Motor Driver L298 CONTROLLER BOARD Now Buy Online Shipping All Across Pakistan COMPANY: MATRIX ELECTRONICS CONTACT PERSON: FAIZAN MUNIR Mobile:0 3002785860 w w w .matrixelectronic . com Email : sales @ matrixelectronic . com Email : info @ matrixelectronic . com

ULN Stepper Motor Driver Board is to use the ULN DARLINGTON ARRAYS to drive the 4-phase 5-wire stepper motor (5v-12v). It's easy to use Arduino or other development platform to drive the stepper motor by this diver board. Box Pack - No Warranty

ULN Stepper Motor Driver Board is to use the ULN DARLINGTON ARRAYS to drive the 4-phase 5-wire stepper motor (5v-12v). It's easy to use Arduino or other development platform to drive the stepper motor by this diver board. Facebook page;ElectronicsArena.com Box Pack - No Warranty

ULN Stepper Motor Driver Board is to use the ULN DARLINGTON ARRAYS to drive the 4-phase 5-wire stepper motor (5v-12v). It's easy to use Arduino or other development platform to drive the stepper motor by this diver board. Facebook page;ElectronicsArena.com

uln 003 stepper motor driver board is to use the uln darling ton arrays to drive the 4 phase 5 wire stepper motor 5v 12v. it s easy to use arduino or other development platform to drive the stepper motor by this diver board. Box Pack - No Warranty

ULN Stepper Motor Driver Board is to use the ULN DARLINGTON ARRAYS to drive the 4-phase 5-wire stepper motor 5v-12v. Its easy to use Arduino or other development platform to drive the stepper motor by this diver board. Box Pack - No Warranty

Overview Dual stepper motor driver shield can drive 2 stepper motors at the same time by Arduino. It can work with the power supply from 4.75V to 30V. High accuracy controlling can be supported by Arduino for CNC milling machine. It uses the same stepper motor driver chip as EasyDriver, so you can use it as 2 EasyDriver modules on board. And there are all pins breakout as 3PIN electronic brick/ sensor brick interface. " Box Pack - No Warranty

Overview Dual stepper motor driver shield can drive 2 stepper motors at the same time by Arduino. It can work with the power supply from 4.75V to 30V. High accuracy controlling can be supported by Arduino for CNC milling machine. It uses the same stepper motor driver chip as EasyDriver, so you can use it as 2 EasyDriver modules on board. And there are all pins breakout as 3PIN electronic brick/ sensor brick interface. " Facebook page;ElectronicsArena.com Box Pack - No Warranty

Overview Dual stepper motor driver shield can drive 2 stepper motors at the same time by Arduino. It can work with the power supply from 4.75V to 30V. High accuracy controlling can be supported by Arduino for CNC milling machine. It uses the same stepper motor driver chip as EasyDriver, so you can use it as 2 EasyDriver modules on board. And there are all pins breakout as 3PIN electronic brick/ sensor brick interface. " Facebook page;ElectronicsArena.com

overview dual stepper motor driver shield can drive 2 stepper motors at the same time by arduino. it can work with the power supply from 4.75v to 30v. high accuracy controlling can be supported by arduino for cnc milling machine. it uses the same stepper motor driver chip as easydriver, so you can use it as 2 easydriver modules on board. and there are all pins breakout as 3pin electronic brick sensor brick interface. " Box Pack - No Warranty

Description The LN298 is a high voltage, high current, dual full-bridge motor driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Comes in a staggered, 15-lead Multiwatt package. Check below for a breakout board. Features Operating supply voltage of up to 46V 4.5-7VDC logic supply voltage Total DC current of up to 4A Low saturation voltage Over-temperature protection Logical 0 input up to 1.5V high-noise immunity