Dual bridge

This dual bidirectional motor driver is based on the very popular L298 Dual H-Bridge Motor Driver Integrated Circuit. The circuit will allow you to easily and independently control two motors of up to 2A each in both directions. It is ideal for robotic applications and well suited for connection to a microcontroller requiring just a couple of control lines per motor. For more details and products and projects call/msg

Dual H-bridge motor driver module Operating mode H-bridge driver (dual) Master chip L298N Logic voltage 5V Drive voltage 5V-35V

Description: Details iShopping.pk brings you the best price for Cisco Wireless-AC Dual Radio Wave 2 Access Point with 2.5GbE LAN Data Sheet (WAP581-E-K9) with 1 year official warranty and express shipping all over Pakistan   Features: ● Concurrent dual-band radio support offers up to 2.1 Gbps on a 5.0-GHz radio and 600 Mbps on a 2.4-GHz radio to use capacity and coverage most efficiently. ● Robust security, including WPA2, 802.1X with RADIUS secure authentication, and rogue access point detection, help protect sensitive business information. ● Wi-Fi Scheduler allows you to control your Wi-Fi network access during business and non-business hours. ● An integrated Wireless Packet Capture tool assists tech support in troubleshooting. ● Intelligent QoS prioritizes network traffic to help keep critical network applications running at top performance. ● Support for power-saving sleep mode and port control features help increase energy efficiency. ● Workgroup Bridge mode lets you expand your network by wirelessly connecting to a second Ethernet network. ● Support for IPv6 lets you deploy future networking applications and operating systems without costly upgrades. ● Sleek design with multiple internal antennas and a versatile mounting kit allows for installation on a ceiling, wall or desktop. ● Offers limited lifetime hardware warranty provides peace of mind.   Specifications: Standards IEEE 802.11ac, 802.11a, 802.11n, 802.11g, 802.11b, 802.3af, 802.3u, 802.1X (security authentication), 802.1Q (VLAN), 802.1D (spanning tree), 802.11i (WPA2 security), 802.11e (wireless QoS), IPv4 (RFC 791), and IPv6 (RFC 2460) Cabling type Category 5e or better Antennas Internal antennas optimized for installation on a wall or ceiling Operating system Linux Software Physical Interfaces Ports 2 GE ports - one 2.5G and second one 10/100/1000 Ethernet, with support for 802.3at at PoE; support is only for port 1 Buttons Reset button Lock slot Slot for Kensington lock LEDs One multifunction LED Physical Specifications Physical dimensions 1.5 x 9.0 x 9.0 in. (38x 229 x 229 mm) (H x W x D) Weight 3 lb (1.4kg) Network Capabilities VLAN support Yes Number of VLANs 1 management VLAN plus 32 VLANs for SSIDs 802.1X supplicant Yes Service Set Identifier (SSID)-to-VLAN mapping Yes Auto-channel selection Yes Spanning tree Yes Load balancing Yes IPv6 Yes ●  IPv6 host support ●  IPv6 RADIUS, syslog, and Network Time Protocol (NTP) Layer 2 802.1Q-based VLANS, 32 active VLANS plus 1 management VLAN Security W-Fi Protected Access (WPA) and WPA2 Yes, including enterprise authentication Access control Yes, management access control list (ACL) plus MAC ACL Secure management Secure HTTP (HTTPS) SSID broadcast Yes Rogue access point detection Yes Mounting and Physical Security Multiple mounting options Mounting bracket included for easy ceiling or wall mounting Physical security lock Kensington lock slot Quality of Service QoS Wi-Fi Multimedia and Traffic Specification (WMM TSPEC) and client QoS Performance Wireless throughput Up to 2.8-Gbps data rate (real-world throughput varies) Recommended user support Up to 200 connective users; 50 active users per radio Multiple Access Point Management Single Point Setup Yes Number of access points per cluster 16 Active clients per cluster 960 Configuration Web user interface Built-in web user interface for easy browser-based configuration (HTTP and HTTPS) Management Management protocols Web browser, Simple Network Management Protocol (SNMP) v3, and Bonjour Remote management Yes Event logging Local, remote syslog, and email alerts Network diagnostics Logging and packet capture Web firmware upgrade Firmware upgradable through web browser; imported or exported configuration file Dynamic Host Configuration Protocol (DHCP) DHCP client IPv6 host Yes HTTP redirect Yes Wireless Frequency Dual concurrent radios (2.4 and 5 GHz) Radio and modulation type Dual radio, orthogonal frequency division multiplexing (OFDM) IEEE 802.11a/n: OFDM (BPSK/QPSK/16QAM/64QAM/256QAM) IEEE 802.11ac: OFDM (BPSK/QPSK/16QAM/64QAM/256QAM) WLAN 802.11n/ac 4 x 4 MU-MIMO at 5 GHz and 3 x 3 MIMO on 2.4 GHz 21 for 20-MHz bandwidth; 9 for 40-MHz bandwidth; 4 for 80-MHz bandwidth 11 for 20-MHz bandwidth; 7 for 40-MHz bandwidth 802.11 dynamic frequency selection (DFS) Data rates supported IEEE 802.11b: DSSS (1/2/5.5/11) IEEE 802.11g: OFDM (6/9/12/18/24/36/48/54) IEEE 802.11n: Refer to the entries for this standard later in this list) IEEE 802.11b: 12.94 MHz IEEE 802.11g: 24.49 MHz EEE 802.11n MCS0 (HT20): 27.44 MHz IEEE 802.11n MCS0 (HT40): 36.18 MHz IEEE 802.11b: 29.76 dBm IEEE 802.11g: 29.24 dBm IEEE 802.11n MCS0 (HT20): 29.25 dBm IEEE 802.11n MCS0 (HT40): 23.81 dBm Frequency band and operating channels Frequency Band Channel No. Frequency Channel No. Frequency 2400~2483.5MHz 1 2412 MHz 7 2442 MHz 2 2417 MHz 8 2447 MHz 3 2422 MHz 9 2452 MHz 4 2427 MHz 10 2457 MHz 5 2432 MHz 11 2462 MHz 6 2437 MHz - - Frequency Band Channel No. Frequency Channel No. 5150- to 5250-MHz Band 1 36 5180 MHz 44 38 5190 MHz 46 40 5200 MHz 48 42 5210 MHz - 52 5260 MHz 60 54 5270 MHz 62 5250- to 5350-MHz Band 2 56 5280 MHz 64 58 5290 MHz - 100 5500 MHz 112 102 5510 MHz 116 104 5520 MHz 132 5470- to 5725-MHz Band 3 106 5530 MHz 134 108 5540 MHz 136 110 5550 MHz 140 149 5745 MHz 157 151 5755 MHz 159 5725- to 5850-MHz Band 4 153 5765 MHz 161 155 5775 MHz 165 Transmitted output power Transmitted Output Power: 2.4 GHz ●  802.11b: 20.0 +/– 1.5 dBm @ CH6, all rates ●  802.11g: 20.0 +/– 1.5 dBm@ CH6, 6 Mbps ●  802.11g: 17.0 +/– 1.5 dBm@ CH6, 54 Mbps ●  802.11n(HT20): 20.0 +/– 1.5 dBm@ CH6, MCS0 ●  802.11n(HT20): 17.0 +/– 1.5 dBm@ CH6, MCS7 ●  802.11n(HT40): 16.0 +/– 1.5 dBm@ CH6, MCS7 5-GHz UNII-1 (5150~5250 MHz) ●  802.11a: 22.0 +/– 2 dBm @ 6 Mbps ●  802.11a: 20.0 +/– 2 dBm @ 54 Mbps ●  802.11ac(VHT20): 22.0 +/– 2 dBm @ MCS0 ●  802.11ac(VHT20): 14.0 +/– 2 dBm @ MCS8 ●  802.11ac(VHT40): 21.0 +/– 2 dBm @ MCS0 ●  802.11ac(VHT40): 14.0 +/– 2 dBm @ MCS9 ●  802.11ac(VHT80): 20.0 +/– 2 dBm @ MCS0 ●  802.11ac(VHT80): 14.0 +/– 2 dBm @ MCS9 5-GHz UNII-2 (5250–5350 MHz)/UNII-2 Extended (5470–5725 MHz) ●  802.11a: 22.0 +/– 2 dBm @ 6 Mbps ●  802.11a: 20.0 +/– 2 dBm @ 54 Mbps ●  802.11ac(VHT20): 22.0 +/– 2 dBm @ MCS0 ●  802.11ac(VHT20): 14.0 +/– 2 dBm @ MCS8 ●  802.11ac(VHT40): 21.0 +/– 2 dBm @ MCS0 ●  802.11ac(VHT40): 14.0 +/– 2 dBm @ MCS9 ●  802.11ac(VHT80): 20.0 +/– 2 dBm @ MCS0 ●  802.11ac(VHT80): 14.0 +/– 2 dBm @ MCS9 5GHz UNII-3 (5725~5850MHz) ●  802.11a: 22.0 +/– 2 dBm @ 6 Mbps ●  802.11a: 20.0 +/– 12 dBm @ 54 Mbps ●  802.11ac(VHT20): 22.0 +/– 2 dBm @ MCS0 ●  802.11ac(VHT20): 14.0 +/– 2 dBm @ MCS8 ●  802.11ac(VHT40): 21.0 +/– 2 dBm @ MCS0 ●  802.11ac(VHT40): 14.0 +/– 2 dBm @ MCS9 ●  802.11ac(VHT80): 20.0 +/– 2 dBm @ MCS0 ●  802.11ac(VHT80): 14.0 +/– 2 dBm @ MCS9 Wireless isolation Wireless isolation between clients External antennas None Internal antennas 4 Internal fixed PIFA antenna Antenna gain in dBi 3.61 dBi @2.4 GHz; 6.23 dBi @5 GHz Receiver sensitivity 2.4 GHz ●  802.11b: –86 dBm @ 11Mbps ●  802.11g: –73 dBm @ 54 Mbps ●  802.11n(HT20): –71 dBm @ MCS7 ●  802.11n(HT40): –67 dBm @ MCS7 5GHz ●  802.11a: –90 dBm @ 6 Mbps ●  802.11a: –74 dBm @ 54 Mbps ●  802.11ac(VHT20): –66 dBm @ MCS8 ●  802.11ac(VHT40): –62 dBm @ MCS9 ●  802.11ac(VHT80): –58 dBm @ MCS9 Wireless distribution system (WDS) Yes Fast roaming Yes Multiple SSIDs 16 per radio Wireless VLAN map Yes WLAN security Yes Wi-Fi Multimedia (WMM) Yes, with unscheduled automatic power save Operating Modes Access point Access point mode, Wireless Domain Services (WDS) bridging, and Workgroup Bridge mode Environmental Power options IEEE 802.3at/af Ethernet switch Cisco power injector: SB-PWR-INJ2-xx Cisco power adapter: SB-PWR-48v-xx Peak power: 18 watts Compliance Safety: ●  UL 60950-1 ●  CAN/CSA-C22.2 No. 60950-1 ●  IEC 60950-1 ●  EN 60950-1 Radio approvals: ●  FCC Part 15.247, 15.407 ●  RSS-210 (Canada) ●  EN 300.328, EN 301.893 (Europe) ●  AS/NZS 4268.2003 (Australia and New Zealand) EMI and susceptibility (Class B): ●  FCC Part 15.107 and 15.109 ●  ICES-003 (Canada) ●  EN 301.489-1 and -17 (Europe) Operating temperature 32 to 104°F) (0 to 40°C) Storage temperature –4 to 158°F (–20 to 70°C) Operating humidity 10 to 85% noncondensing Storage humidity 5 to 90% noncondensing System memory 256-MB RAM 128-MB flash

AOA All PLEASE READ THE AD CAREFULLY I am selling my laptop Asus X54H for just rs (Price Reduced), excluding shipping. Ye sandy bridge technology ka hai and asus ki site kehti hai kay ye core i3 bhi support karta hai tau agar aap ye le kar i3 daaltay hain tau performance achi ho jai gi. The specs are as follows: intel celeron C PU BGhz Dual Core (sandy bridge) 4gb ddr3 ram 160gb SATA HDD Super Drive Intel Hd Graphics Battery back-up is around 1 hr depending on ur use and the profile u have set. The charger is non genuine, it is from NEC the condition is normal and can be seen in the pics. There are some issues that i would like to mention: - number keys nahi chaltay likin numberpad hai tau uski zaroorat iss se puri ho jati hai tau masla nahi hai itna. - Screen pe two spots hain and aik sqaure hai jo aap pics mein dekh saktay hain (bios waali pic and uss pic mein jis mein screen thori tilted hai). jo square hai wo screen tilt kiyay beghair nazar nahi aata. - lan port nahi chalta. drivers install ho jatay hain and detect bhi hota hai but wire daalo tau kuch nahi hota. - charging pin shaid loose hai as jub cable lagao and press karo tau charge karta hai and agar press na karo tau nahi charge karay ga. Mein lahore se hoon. aap payment se pehlay check kar saktay hain. also shipping kiya ja sakta hai likin saraa risk and expense buyer ka ho ga. agar koi interested hai lainay mein tau mujay pm ya sms karein on Thanks Condition: 8/10 - No Warranty

Key FeaturesThe L298 Stepper Controller makes it easy to drive either two DC motors or a bipolar stepper motor. Double H bridge driveChip L298N (ST NEW)Logical voltage 5VDrive voltage 5V-35VLogic current 0mA-36mADrive current 2A(MAX single bridge)Storage temperature -20 to +135Max power 25W Small size mm (approx 1.75"" x 1.75"" x 1"")Compatible with L297/L298 driver Specifications Material Dimensions (cm) Weight (kg) Mixed Material 4.3 x 4.3 x " Box Pack - No Warranty

Key FeaturesThe L298 Stepper Controller makes it easy to drive either two DC motors or a bipolar stepper motor. Double H bridge driveChip L298N ST NEW. Logical voltage 5VDrive voltage 5V-35VLogic current 0mA-36mADrive current 2A(MAX single bridge)Storage temperature -20 to +135Max power 25W Small size 43x43x27mm Compatible with L297/L298 driver Specifications Material Dimensions in cm Weight in kg Mixed Material 4.3 x 4.3 x " Facebook page;ElectronicsArena.com Box Pack - No Warranty

Key FeaturesThe L298 Stepper Controller makes it easy to drive either two DC motors or a bipolar stepper motor. Double H bridge driveChip L298N ST NEW. Logical voltage 5VDrive voltage 5V-35VLogic current 0mA-36mADrive current 2A(MAX single bridge)Storage temperature -20 to +135Max power 25W Small size 43x43x27mm Compatible with L297/L298 driver Specifications Material Dimensions in cm Weight in kg Mixed Material 4.3 x 4.3 x " Facebook page;ElectronicsArena.com

Key FeaturesThe L298 Stepper Controller makes it easy to drive either two DC motors or a bipolar stepper motor. Double H bridge driveChip L298N ST NEW. Logical voltage 5VDrive voltage 5V-35VLogic current 0mA-36mADrive current 2A(MAX single bridge)Storage temperature -20 to +135Max power 25W Small size 43x43x27mm Compatible with L297/L298 driver Specifications Material Dimensions in cm Weight in kg Mixed Material 4.3 x 4.3 x " Box Pack - No Warranty

key featuresthe l298 stepper controller makes it easy to drive either two dc motors or a bipolar stepper motor. double h bridge drivechip l298n st new logical voltage 5vdrive voltage 5v 35vlogic current 0ma 36madrive current 2a max single bridge storage temperature 20 to plus 135max power 25w small size 43x43x27mm approx 1.75 x 1.75 x 1 compatible with l297 l298 driver specifications material dimensions cm weight kg mixed material 4.3 x 4.3 x

maximum current rating: 30a maximum voltage: 41v mosfet on resistance: 19mohm per leg maximum pwm frequency: 20khz undervoltage and overvoltage shutdown the monster motor controller shield for arduino 14a, v is essentially a ramped up version of sparkfun s ardumoto motor driver shield. for this monster shield maufacturer has replaced the l298 h bridge with a pair of vnh2sp30 full bridge motor drivers. manufacturer has also beefed up the support circuitry so this board is capable of driving a pair of high current motors." Box Pack - No Warranty

Features: Double H bridge drive Chip L298N (ST NEW) Logical voltage 5V Drive voltage 5V-35V Logic current 0mA-36mA Drive current 2A(MAX single bridge) Storage temperature -20 to +135 Max power 25W Weight 30g Small size mm (approx 1.75"" x 1.75"" x 1"") Compatible with L297/L298 driver Note This module has a built-in 5v power supply for external use. Drive voltage is 7v-35v. DO NOT input voltage to +5v supply interface - this is OUTPUT only." Box Pack - No Warranty

Features Double H bridge drive Chip L298N ST NEW Logical voltage 5V Drive voltage 5V-35V Logic current 0mA-36mA Drive current 2AMAX single bridge Storage temperature -20 to 135 Max power 25W Weight 30g Small size 434327mm approx 1.75 x 1.75 x 1 Compatible with L297L298 driver Note This module has a built-in 5v power supply for external use. Drive voltage is 7v-35v. DO NOT input voltage to 5v supply interface - this is OUTPUT only.

maximum current rating 30a maximum voltage 41v mosfet on resistance 19mohm per leg maximum pwm frequency 20khz undervoltage and overvoltage shutdown the monster motor controller shield for arduino 14a, 5.5 16v is essentially a ramped up version of sparkfun s ardumoto motor driver shield. for this monster shield maufacturer has replaced the l298 h bridge with a pair of vnh2sp30 full bridge motor drivers. manufacturer has also beefed up the support circuitry so this board is capable of driving a pair of high current motors.

Asalamualaikum Friends i Want to Sale PC Stuff MOTHERBOARD + PROCESSOR (Condition Very Very Less used FRESH IN SHA ALLAH apko dekhte hi pasand aye ga u can see the ORIGNAL pics) MotherBoard: ASUS P8H61-M LE (Support 2ND & 3RD GENRATION PROCESSOR) (REV 3.0 - New H61 B3 Revision Get better graphics with iGPU Boost on H61 platform) Condition Rs./= Specs: https://www.asus.com/Motherboards/P8H61M_LE/ Processor: Intel® Pentium® Processor G620 Dual Core Sandy Bridge LGA M Cache, 2.60 GHz) with (2 Years Warrenty Left) Condition Rs./= Specs: http://ark.intel.com/products// Both Price Rs./= Contact: Amir

Seller Type: An Individual Condition: New i Ivy Bridge Dual-Core 3.3GHz LGA W Desktop Processor Intel HD Graphics Condition: Brand New Package: ONLY chip WITH HSF Warranty: 3 Days Checking Warranty Market Price: My Price: Dead Final (Plz Do not contact me if u not agree with my price) NO FOOLISH OFFERS PLZ CALL /SMS: Call me at: .

Manufacturer Part Number L293D Description IC MOTOR DRIVER PAR 16-DIP Lead Free Status RoHS Status Lead free RoHS Compliant Standard Package 25 Category Integrated Circuits ICs Family PMIC - Motor Drivers, Controllers Series - Motor Type - Stepper Bipolar Motor Type - AC, DC Brushed DC Function Driver - Fully Integrated, Control and Power Stage Output Configuration Half Bridge 4 Interface Parallel Technology - Step Resolution - Applications General Purpose Current - Output 600mA Voltage - Supply 4.5 V 36 V Voltage - Load 4.5 V 36 V Operating Temperature -40C 150C TJ Mounting Type Through Hole Package Case 16-DIP 0.300, 7.62mm Supplier Device Package 16-PowerDIP Online Catalog Drivers

D-Link DWL-6610AP Wireless AC1200 Dual‑Band Unified Access Point Product Status The DWL-6610AP is an affordable, Unified Wireless AC1200 Access Point, enabling businesses of all sizes create the fastest wireless network possible.  With a sleek and stylish design, the DWL-6610AP can be discreetly deployed anywhere. Performance without Compromise       The DWL-6610AP is an affordable, Unified Wireless AC1200 Access Point, enabling businesses of all sizes create the fastest wireless network possible. With a sleek and stylish design, the DWL-6610AP can be discreetly deployed anywhere. Key Features Wireless AC 1200 Maximum combined wireless speed of 1200 Mbps.* Broadcast on 32 SSIDs Simultaneously Supports up to 32 SSIDs, 16 per radio, including station isolation. Dual Band Supports both 2.4Ghz and 5Ghz bands simultaneously. Unified Wireless Access points can be managed by unified wireless controller. Smart Design The DWL-6610AP can be mounted easily onto any wall or ceiling without looking out of place in an office or home. Enclosed in a plenum-rated UL2043 certified housing, the DWL-6610AP adheres to strict fire codes for placement in air passageways. Band Steering technology With band steering, the DWL-6610AP detects whether or not the wireless client is dual-band capable, and if so, it pushes the client to connect to the less congested 5 Ghz band. It does this by actively blocking the client’s attempts to associate with the 2.4 Ghz network. Versatility Built as standard Whether you intend to use a single Access Point or roll out a large corporate network, the DWL-6610AP coupled with a D-Link Wireless Controller or Unified Switch makes managing your wireless network simple. Secure and Green Design The DWL-6610AP has a wireless scheduler feature, which turns off wireless functionality when it isn’t needed, saving power and increasing network security.   Fast Seamless Roaming Combining the DWL-6610AP with a Unified Wireless Switch or Controller allows you to create a wireless network that enables people to move freely around a building without losing connectivity.     Management platforms D-Link’s Unified Wireless Access Points can be managed using a D-Link Wireless Controller or Unified Switch.   Simultaneous Dual-Band Supports up to 867 Mbps 2x2 MIMO for the 5Ghz band and up to 300Mbps 2x2 MIMO for the 2.4Ghz band   * Maximum wireless signal rate derived from IEEE standard 802.11ac specifications which are subject to change. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental factors may adversely affect wireless signal range. Specs Type Hardware-managed AP Wireless standard Wireless AC Frequency band mode Dual-band simultaneous Wireless speed 300 Mbps 2.4 GHz  867 Mbps 5 GHz Antenna type Embedded omni-directional antennas Antenna gain 3.5 dBi for 2.4 GHz  5 dBi for 5 GHz Power-over-Ethernet Yes Wired interface 1 x Gigabit Ethernet LAN Console port   Indoor/outdoor Indoor Type of housing Plastic Plenum rated (UL-2043)   Wireless modes Access Point (AP)  WDS bridge Advanced features MIMO Maximum number of SSIDs 16 per radio Auto channel selection   WMM-PS/802.11e (U-APSD)   Wi-Fi scheduler   AP traffic load balance   L2 roaming   WPA/WPA2-Personal/Enterprise   TKIP/AES encryption   WLAN partition   SSID broadcast disable   Rogue AP detection   Station isolation   MAC address filtering   802.1X authentication   Wireless controller/unified switch managed features AP load balance  Auto-channel, auto-RF management  Captive portal  L2/L3 fast roaming  Rogue AP mitigation  View neighbour AP information  WIDS/WIPS Supported D-Link Wireless Controllers/Unified Switches DWC-1000  DWC-2000  DWS-4026 Management platform Hardware controller: DWC/DWS Series WEB   SNMP (v1, v2c, v3)   Telnet   SSH   Configuration group sync through AP Array (up to 8 APs)  

Salaam to All I want to sale Intel E dual core Processor and Asus P5G41T-M LX motherboard. 1. Intel E Processor Link: http://ark.intel.com/products//Intel-Pentium-Processor-EM-Cache-3_00-GHz-800-MHz-FSB) Package: Processor and Box with manual Warranty: 7 days check Warranty Condition: Price: 4k fnf 2. Asus P5G41T-M LX Link: http://www.asus.com/Motherboards/Intel_Socket_775/P5G41TM_LX/#specifications Package: Mobo and each and everything that comes with it; Warranty: 4 months warranty remaining; Condition: Price: 4.2k fnf 3. ATI HIS mb DDRbit Gaming Card Link: http://www.hisdigital.com/un/product.shtml Package: Card, Hdmi to Dvi Converter, crossfire bridge manuals and box Warranty: 7 days chech warranty Condition: Price: 7k fnf 4. Coolmax Branded Power Supply Link: http://www.coolmaxusa.com/productDetailsPower.asp?item=V-600&details=spec&subcategory=140mm&category=single Package: Just Power Supply Warranty: 7 days check warranty Condition: Price: 2.5k fnf Location: Rawalpindi/ Islamabad but shipment is also possible to other cities. Contact: - Condition: - Warranty: 4 Months

D-Link 1300Mbps Mngd 11AC Wave2 MU-MIMO Dual Bnd AP PoE Gigabit Port The DAP-2610 Wireless AC1300 Wave 2 Dual-Band PoE Access Point is designed to support small to medium business or enterprise environments by providing network administrators with secure and manageable dual-band wireless LAN options, and utilizing the cutting-edge speed of Wireless AC. Blazing Wireless Wave 2 AC Performance The DAP-2610 delivers reliable, high-speed wireless performance using the latest 802.11ac Wave 2 standard with maximum wireless signal rates of up to 400 Mbps (256-QAM) over the 2.4 GHz band, and 900 Mbps over the 5 GHz band1. This, coupled with support for the Wi-Fi Multimedia™ (WMM) Quality of Service (QoS) feature, makes it an ideal access point for audio, video, and voice applications. When enabled, QoS allows the DAP-2610 to automatically prioritize network traffic according to the level of interactive streaming, such as HD movies or VoIP. The QoS feature can be adjusted through the DAP-2610 web GUI using a drop-down menu to select customized priority rules. Additionally, the DAP-2610 supports load balancing to ensure maximum performance by limiting the maximum number of users per access point. Versatile Access Point Functionality The DAP-2610 allows network administrators to deploy a highly manageable and extremely robust simultaneous dual-band wireless network. The DAP-2610 can provide optimal wireless coverage over either the 2.4 GHz (802.11b, 802.11g, and 802.11n) or the 5 GHz (802.11a, 802.11n, and 802.11ac) bands. The DAP-2610 can be ceiling mounted, wall mounted, or placed on a desktop to meet any wireless demands. For advanced installations, the DAP-2610 has integrated 802.3af Power over Ethernet (PoE) support, allowing the device to be installed in areas where power outlets are not readily available. Security To help maintain a secure wireless network, the DAP-2610 supports both Personal and Enterprise versions of WPA and WPA2 (802.11i), with support for RADIUS server backend and a built-in internal RADIUS server allowing users to create their accounts within the device itself. This access point also includes MAC address filtering, wireless LAN segmentation, SSID broadcast disable, rogue AP detection, and wireless broadcast scheduling for further protection of your wireless network. The DAP-2610 includes support for up to eight VLANs per band, allowing multiple SSIDs to be implemented and further segment users on the network. It also includes a wireless client isolation mechanism, which limits direct client-to-client communication. Additionally, the DAP-2610 supports Network Access Protection (NAP), a feature of Windows Server® 2008, allowing network administrators to define multiple levels of network access based on individual client’s needs. Multiple Operation Modes To maximize total return on investment, the DAP-2610 can be configured to optimize network performance based on any one of its multiple operation modes: Access Point, Wireless Distribution System (WDS), a WDS with Access Point, and Wireless Client. With WDS support, network administrators can set up multiple DAP-2610s throughout a facility and configure them to bridge with one another, while also providing network access to individual clients. The DAP-2610 also features advanced features such as load balancing and redundancy, for fail-safe wireless connectivity. Network Management Network administrators have multiple options for managing the DAP-2610, including Web (HTTP), Secure Socket Layer (SSL), Secure Shell (SSH), and Telnet. For advanced network management, administrators can use the D-Link Central Wi-Fi Manager to configure and manage multiple access points from a single location. In addition, the D-Link Central Wi-Fi Manager provides network administrators with the means of conducting regular maintenance checks remotely, eliminating the need for sending out personnel to physically verify proper operation. The DAP-2610 also has a wireless scheduling feature, turning off wireless functionality when it is not needed to save power. With simultaneous dual-band functionality, PoE support, extensive manageability, versatile operation modes, and solid security enhancements, the DAP-2610 provides small to medium business and enterprise environments with a business-class solution for deploying a wireless network. Techinical Specification Device Interfaces •1 IEEE 802.11a/b/g/n/ac Wave2 wireless              •1 Gigabit LAN (supports PoE) Standards  • IEEE 802.11a/b/g/n/ac                                                                 • IEEE 802.3u/ab                                                                                                                                                                                                         • IEEE 802.3az Energy Efficient Ethernet (EEE)                         • IEEE 802.3af Power over Ethernet Antennas  • 2  internal dual-band   3dBi omni antennas OperatingFrequency • 2.4 GHz band: 2.4 to 2.4835 GHz                                     • 5 GHz band:5.15 to 5.35 GHz, 5.47 to 5.85 GHz Maximum Output Power • 20dBm for 2.4 GHz                                                            • 20 dBm for 5 GHz Data Signal Rate • 2.4 GHz                                                                            • 5 GHz                         • Up to 400 Mbps                                                              • Up to 867 Mbp Functionality Security • WPA - Personal                                                                    • SSID broadcast disable • WPA - Enterprise                                                                  • MAC address access control • WPA2 - Personal                                                                  • Network Access Protection (NAP) • WPA2 - Enterprise                                                                • Internal RADIUS server • WEP 64 / 128 - bit encryption Network Management • Telnet                                                                                • Traffi ccontrol • Secure Telnet (SSH)                                                      • SNMP v1 / v2c / v3 • Web (HTTP)                                                                     • D-Link Central Wi-Fi Manager • Secure Socket Layer (SSL)                                           • AP Array LEDs • Power / status Physical Dimensions • 170 x 170 x 28mm (6.69 x 6.69 x 1.1 inches) Weight • 314g (0.69 lbs) without mounting base                                       • 370.6g (0.82 lbs) with mounting base Power Supply • External power adapter: 12V/1A                                                    • IEEE 802.3 af PoE Maximum Power Consumption • 12W Temperature • Operating: 0 to 40°C (32 to104°F)                                                 • Storage: -20 to 65°C (-4 to149°F) Humidity • Operating:10% to 90% non-condensing                                     • Storage: 5% to 95% non-condensing Meantime Between Failure (MTBF) • > 30,000 hours Certifications • FCC                                                                                  • UL • IC                                                                                      • Wi-Fi® Certified • CE4

Description The LN298 is a high voltage, high current, dual full-bridge motor driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Comes in a staggered, 15-lead Multiwatt package. Check below for a breakout board. Features Operating supply voltage of up to 46V 4.5-7VDC logic supply voltage Total DC current of up to 4A Low saturation voltage Over-temperature protection Logical 0 input up to 1.5V high-noise immunity

Processor: intel core i7 3770 3.4Ghz 8mb cache Heat sink: cooler master hyper 103 Motherboard: gigabyte ga-h77-ds3h Ram: Corsair vengeance dual channel 8gb (4gbx2) 1600Mhz Power supply: Zalman ZM700-GV 80+ Bronze PSU. Gaming Case: Antec six hundred se Casing with 5 blue led fans. Total demand is 36k, keep in mind that im not gonna accept absurdly low offers. Also i'm gonna look to sell the whole pc. Don't want a useless shell lying around. location is karachi. Call or whatsapp only

Maximum current rating: 30A Maximum voltage: 41V MOSFET on-resistance: 19mOhm Maximum PWM frequency: 20kHz Undervoltage and overvoltage shutdown The Monster Motor Controller Shield For Arduino 14A, V is essentially a ramped up version of Sparkfun's Ardumoto motor driver shield. For this monster shield maufacturer has replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. Manufacturer has also beefed up the support circuitry so this board is capable of driving a pair of high-current motors." Facebook page;ElectronicsArena.com Box Pack - No Warranty

Maximum current rating: 30A Maximum voltage: 41V MOSFET on-resistance: 19mOhm Maximum PWM frequency: 20kHz Undervoltage and overvoltage shutdown The Monster Motor Controller Shield For Arduino 14A, V is essentially a ramped up version of Sparkfun's Ardumoto motor driver shield. For this monster shield maufacturer has replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. Manufacturer has also beefed up the support circuitry so this board is capable of driving a pair of high-current motors." Facebook page;ElectronicsArena.com

Maximum current rating: 30A Maximum voltage: 41V MOSFET on-resistance: 19mOhm Maximum PWM frequency: 20kHz Undervoltage and overvoltage shutdown The Monster Motor Controller Shield For Arduino 14A, V is essentially a ramped up version of Sparkfun's Ardumoto motor driver shield. For this monster shield maufacturer has replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. Manufacturer has also beefed up the support circuitry so this board is capable of driving a pair of high-current motors." Box Pack - No Warranty

Maximum current rating: 30A Maximum voltage: 41V MOSFET on-resistance: 19mOhm Maximum PWM frequency: 20kHz Undervoltage and overvoltage shutdown The Monster Motor Controller Shield For Arduino 14A, V is essentially a ramped up version of Sparkfun's Ardumoto motor driver shield. For this monster shield maufacturer has replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. Manufacturer has also beefed up the support circuitry so this board is capable of driving a pair of high-current motors."

i want to sale Acer Q45T-AM Motherboard Processor Support – Intel Core 2 Quad, Core 2 Duo, Pentium Dual Core, Celeron Dual Core Socket Type: LGA775 Chipset* North Bridge – Intel Q45* South Bridge – Intel ICH10 Integrated Graphics: Intel GMA x FSB MHz Expansion Slots1 x PCI Express x x PCI Express x12 x PCI Storage6 x SATAII 3Gb/s connectorsSupports HDDs, Internal Solid State Drive (SSD) Audio: Realtek ALC888 – High Definition Ethernet Intel Gigabit – Mb/s Memory: 4 x 240-pin DDR3 DIMM slots Supports Dual Channel DDR MHz non-ECC, un-buffered memory (Max 8GB) Rear Panel1 x PS/2 green color for mouse 1 x PS/2 purple color for keyboard 1 x RJ45 LAN port 4 x USB 2.0 ports 1 x Serial port 1 x Audio I/O 1 x VGA port 1 x DVI port Internal3 x USB headers1 x Battery socket (3V)1 x Clear CMOS jumper 1 x 4-pin CPU Fan connector1 x 3-pin SYS Rear Fan connector1 x 4-pin ATX 12V Power connector1 x 24-pin ATX Power connector1 x Front Audio header1 x Front Panel header Form FactorMicro-ATX Price final final Condition: - No Warranty

i want to sale Acer Q45T-AM Motherboard Processor Support – Intel Core 2 Quad, Core 2 Duo, Pentium Dual Core, Celeron Dual Core Socket Type: LGA775 Chipset* North Bridge – Intel Q45* South Bridge – Intel ICH10 Integrated Graphics: Intel GMA x FSB MHz Expansion Slots1 x PCI Express x x PCI Express x12 x PCI Storage6 x SATAII 3Gb/s connectorsSupports HDDs, Internal Solid State Drive (SSD) Audio: Realtek ALC888 – High Definition Ethernet Intel Gigabit – Mb/s Memory: 4 x 240-pin DDR3 DIMM slots Supports Dual Channel DDR MHz non-ECC, un-buffered memory (Max 8GB) Rear Panel1 x PS/2 green color for mouse 1 x PS/2 purple color for keyboard 1 x RJ45 LAN port 4 x USB 2.0 ports 1 x Serial port 1 x Audio I/O 1 x VGA port 1 x DVI port Internal3 x USB headers1 x Battery socket (3V)1 x Clear CMOS jumper 1 x 4-pin CPU Fan connector1 x 3-pin SYS Rear Fan connector1 x 4-pin ATX 12V Power connector1 x 24-pin ATX Power connector1 x Front Audio header1 x Front Panel header Form FactorMicro-ATX Price final final

dell optiplex 380 motherboard ddr 3 ram supported with lga 775 socket with intel e processor 3.0 ghz 6m cache complete package.no fault working in good condation. package include processor and mother board board specs: CPU Support Socket LGA 775 – Intel Core 2 Quad, Core 2 Duo, Pentium (Dual Core), Celeron (Dual Core) Chipset * North Bridge – G41 * South Bridge – ICH7 Integrated Graphics Intel (GMA x) FSB MHz Expansion Slots 1 * PCI Express x16 2 * PCI Storage 3 * SATAII 3Gb/s connectors Audio Realtek ALC269 – High Definition Ethernet Broadcom BCM – (Gigabit) RAM -pin) DDR3 DIMM slots Supports Dual Channel DDR MHz non-ECC, un-buffered memory (Max 4GB) Rear Panel 1 * Serial port 1 * Parallel port 1 * Audio I/O – in/out 1 * VGA port 1 * RJ45 LAN Port 6 * USB 2.0 ports Internal 1 * Front Panel header 1 * Password jumper 1 * Clear CMOS jumper 1 * 5-pin CPU Fan connector 1 * 5-pin SYS Rear Fan connector 1 * 4-pin ATX 12V Power connector 1 * 24-pin ATX Power connector 1 * Front Audio header BIOS Form Factor BTX

Acer Q45T-AM Motherboard Specifications. CPU Processor Support – Intel Core 2 Quad, Core 2 Duo, Pentium Dual Core, Celeron Dual Core Socket Type LGA775 Chipset * North Bridge – Intel Q45 * South Bridge – Intel ICH10 Integrated Graphics Intel GMA x FSB MHz Expansion Slots 1 x PCI Express x x PCI Express x1 2 x PCI Storage 6 x SATAII 3Gb/s connectors Supports HDDs, Internal Solid State Drive (SSD) Audio Realtek ALC888 – High Definition Ethernet Intel Gigabit – Mb/s Memory 4 x 240-pin DDR3 DIMM slots Supports Dual Channel DDR MHz non-ECC, un-buffered memory (Max 8GB) Rear Panel 1 x PS/2 green color for mouse 1 x PS/2 purple color for keyboard 1 x RJ45 LAN port 4 x USB 2.0 ports 1 x Serial port 1 x Audio I/O 1 x VGA port 1 x DVI port Internal 3 x USB headers 1 x Battery socket (3V) 1 x Clear CMOS jumper 1 x 4-pin CPU Fan connector 1 x 3-pin SYS Rear Fan connector 1 x 4-pin ATX 12V Power connector 1 x 24-pin ATX Power connector 1 x Front Audio header 1 x Front Panel header Form Factor Micro-ATX Condition: , Working .... Contact: - Box Open - Never Used - No Warranty

Acer Q45T-AM Motherboard Specifications. CPU Processor Support – Intel Core 2 Quad, Core 2 Duo, Pentium Dual Core, Celeron Dual Core Socket Type LGA775 Chipset * North Bridge – Intel Q45 * South Bridge – Intel ICH10 Integrated Graphics Intel GMA x FSB MHz Expansion Slots 1 x PCI Express x x PCI Express x1 2 x PCI Storage 6 x SATAII 3Gb/s connectors Supports HDDs, Internal Solid State Drive (SSD) Audio Realtek ALC888 – High Definition Ethernet Intel Gigabit – Mb/s Memory 4 x 240-pin DDR3 DIMM slots Supports Dual Channel DDR MHz non-ECC, un-buffered memory (Max 8GB) Rear Panel 1 x PS/2 green color for mouse 1 x PS/2 purple color for keyboard 1 x RJ45 LAN port 4 x USB 2.0 ports 1 x Serial port 1 x Audio I/O 1 x VGA port 1 x DVI port Internal 3 x USB headers 1 x Battery socket (3V) 1 x Clear CMOS jumper 1 x 4-pin CPU Fan connector 1 x 3-pin SYS Rear Fan connector 1 x 4-pin ATX 12V Power connector 1 x 24-pin ATX Power connector 1 x Front Audio header 1 x Front Panel header Form Factor Micro-ATX Condition: , Working .... Contact: -