Cat 6a ethernet cable 2

【Shielded from interference】 Made of 4 shielded twisted pair (STP) of copper wires with two RJ45 connectors on each end. Compared to the Cat 6 network Ethernet cable, the additional shielding and improved quality in twisting of the wires provides better protection from crosstalk, noise, and interference that can degrade the signal quality DESIGN FOR FEELING: The clip protector keeps the RJ45 connector from unwanted snags while routing the cable. 【Product Features】 1. Standard: Cat 7,SSTP; Meet TIA/EIA-568-B.2-10 Specfications,Backward compatible with Cat 5e / Cat 6 / Cat 6a Ethernet Cable 2. Conductor Construction: 8 wires Stranded Copper with shielding, much better than performance than copper clad aluminum (CCA) wire 3. Support bandwidth upto 600Mhz 4. Support speed up to 10Gbps 5. 28AWG, OD:6.3 mm 6. Gold Plated RJ45 connectors for optimized signal quality 7. 4PR UTP copper strands for minimal noise, interference & crosstalk 8. Tough, yet flexible PVC jacket & heavy-duty, snag-less mold 【10Gbps Speed and Multi-shielded Cable】 Ugreen Cat7 network Ethernet cable is capable of transmitting data at speed up to 10Gbps over 100m run of cable. It is made out of 4 shielded twisted pair (STP) of copper wires with two RJ45 connectors on each end. Compared to the Cat 6 network Ethernet cable, the additional shielding and improved quality in twisting of the wires provides better protection from crosstalk, noise, and interference that can degrade the signal quality. 【Universal Compatibility】 Ugreen Network Ethernet cables offer universal connectivity to computers and network components, such as routers, switches, hubs, network printers, game boxes and network attached storage devices, Xbox, PS2,PS3,Ps4 and game boxes whit RJ45 port. 【One-Sec Installation】 Plug-&-play: Ready to use, once each end is connected to a respective port on a compatible device

Fluke DTX-QUAD-OTDR Kit DTX-1800 Cable Analyzer for sale $3, 740 USD INCLUDED Fluke Networks DTX 1800 CableAnalyzer Fluke Networks DTX 1800 SmartRemote Fluke Networks DTX-QUAD-OTDR Module Single mode 1310nm 1550nm Multimode 850nm 1300nm VFL (2) Interchangeable SC Connectors (2) Fluke Networks DTX-PLA002 CAT 6A Link Adaptors (2) Fluke Networks DTX-CHA001 CAT 6 Channel Adaptors Fluke Networks 62.5 Micron Mandrel Fluke Networks 50mm Mandrel Fiber Cables: (2) 50 Micron Duplex (2) MM SC-SC Stand For Module (2) Headset TalkSets Fluke Networks LinkWare Software (2) AC Adapter/Chargers USB PC Interface Cable User Manual On CD-ROM (2) Straps For DTX-1800 Carrying Case

Product Name:POE Injector / Splitter Data PIN:1/2,3/6 Power PIN:4/5+ & 7/8- Data in:Connects PC/HUB/Switch Dimensions:50mm*25mm*25mm Case of material:ABS 94V-0 Ethernet Data rate:10/100/1000 Mbp Ethernet Cable:TIA/EIA 568 Cat.5 Ethernet Cable Connector:RJ-45 Operating Temperature:0- 40 Degree Storage Temperature:-40-70 Degree Operating Humidity:10%to80% RH Storage Humidity:5%to90% RH

Description: Details iShopping.pk brings you the best price for ClearOne Converge Pro 2 128V Audio DSP Mixer with express shipping all over Pakistan.   The CONVERGE Pro 2 128V Audio DSP Mixer from ClearOne is a complete conferencing solution with 12 mic/line inputs (AEC), 8 mic/line outputs, built-in USB audio, and built-in VoIP interface for 2 lines. It is optimized to work with Beamforming Mic Array 2 and DIALOG 20 2-Channel Wireless Microphone System through its native connection. The mixer comes with built-in VoIP for VoIP conferencing. The mixer is suitable for use in venues such as boardrooms, conference rooms, huddle rooms, training rooms, lecture halls, courtrooms, auditoriums, and telemedicine facilities.   Features: Architecture • 12 mic/line inputs with AEC •  Built-in VoIP for 2 lines •  Built-in USB for PC-based conferencing Scalable Connectivity •  Standalone and daisy-chained system •  Stack up units up to 96 mic/line inputs •  Expansion bus C-Link with 64 channels •  P-Link bus to connect 6 peripherals Configuration & Management •  CONSOLE software •  Auto-discovery of devices •  Matrix View for entire system •  FlowView for visualized audio signal paths •  System monitoring and troubleshooting Audio Signal Processing •  Acoustic Echo Cancellation processing •  Distributed Echo Cancellation on every mic input •  Noise cancellation with Adaptive-Ambience •  Acoustic Intelligence with faster convergence •  DARE feedback elimination •  Microphone gating Flexible Control Options •  Dialer app for Windows, Mac, iOS, and Android •  Tabletop controller with a touch panel •  Wall controller with buttons •  Web-based controller Supports 3rd-party control modules   Specifications: Mic/Line Inputs Balanced audio inputs, 3.81 mm orange color Phoenix/Euroblock type male header Push-on mini-terminal block Outputs Balanced audio inputs, 3.81 mm black color Phoenix/Euroblock type male header Push-on mini-terminal block Frequency Response 20 Hz to 22 kHz @ +4 dBu, +/- 0.5 dBu EIN 20 kHz BW, max gain, Rs: 150 Ohms, -126 dBu THD + N 20 Hz to 22 kHz @ +4 dBu, line level, 0.006% 20 Hz to 22 kHz @ -56 dBu, mic level, Dynamic Range 20 Hz to 20 kHz @ 0 dB, >105 dB Crosstalk Channel to Channel Stimulus at 20 dBu to receptor at -56 dBu, 1 kHz, Input Impedance Balanced (line to ground), 2.2 kOhms, 1% Nominal Input Level Adjustable -56 dB to 0 dB, 7 dB step coarse gain Maximum Input Level -65 dBu to 20 dBu Phantom Power 48 V, Impedance: 6.81 kOhms Output Impedance Balanced (Line to Ground): 95 Ohms, 1% Output Level 0 dBu (Nominal), 20 dBu (Max), -40 dBu (Selectable) USB Audio Port Type: USB-B connector Audio: Digital audio, 2 x 2 bidirectional channels Sample Rate: 48 kHz Sample Bit Depth: 24-bit Compatible: USB 2.0, USB 3.0 Telephone Interface Port Type: RJ11   Frequency Response: Mic/Line Input to Telephone Out: 250 Hz to 3.4 kHz, +/- 2 dB, 4 dBu Telephone In to Mic/Line Out: 250 Hz to 3.4 kHz, +/- 2 dB, -15 dBu   THD + N: Mic/Line Input to Telephone Out: Telephone In to Mic/Line Out:   Dynamic Range: Mic/Line Input to Telephone Out: >67 dBu Telephone In to Mic/Line Out: >87 dBu   REN: Ringer Equivalent Number 0.2   Transhybrid Balance: 30 dB (1 kHz, all AC terminations) VoIP Port Type: RJ-45, 10/100 Mbps Ethernet network, auto negotiation Audio: 5 lines (2 default + 3 lines through license), each line supporting 1+5 calls Sample Rate: 24 kHz Sample Bit Depth: 24-bit Codec: G.711 uLaw, G.711 ALaw, G.722 Ethernet Port Type: RJ-45, 10/100 Mbps Ethernet network, auto negotiation IP Address: IPv4 (IPv6 upgradeable) Bus C-LINK Expansion Bus Ports Type: RJ-45 (CAT5e or CAT6) C-Link In & Out: Proprietary expansion bus Audio: 64 expansion channels Cable: Solid core, factory-terminated CAT5e or 6 cable Distance: Up to 150' (45 m) Ports Type: RJ-45 (CAT5e or CAT6) P-Link In & Out: Proprietary peripheral bus PoE In: P-Link in port, PoE IEEE802.3AF Audio: Up to 3 Beamforming Microphone Array 2 units + up to 3 DIALOG 20 Wireless Receiver units Cable: Solid core, factory-terminated CAT 5e or 6 cable Distance: Up to 200' (60 m) RS232 Port Type: DB9 female Settings: 9600/19200/38400/57600/115200 baud Serial echo Flow control Support: Serial commands GPIO Port Type: 5.08 mm Green color Phoenix/Euroblock type male header Support: Control, status, variable voltage control Power Pin: 5 VDC @ 350 mA power source Pin 1 to 4 Open Collector Outputs: 40 VDC @ 250 mA Active Outputs (Source/Sink): 5 VDC @ 25 mA Logic Inputs: 40.2 kOhms pull up Variable Voltage Control Inputs: 5 VDC maximum Ground Pin: GND USB Port Type: USB-B connector Location: Front panel Compatible: USB 2.0, USB 3.0 LEDs Location: Front panel Status LED (Off): Unit still initializing Status LED (Blue, Fast Blinking): Stack syncing in progress Status LED (Blue, Slow Blinking): Unit not configured Status LED (Blue, Solid): Configured unit Status LED (Red, Fast Blinking): Stack sync error Locate LED (Blue, Blinking): "Unit locate" command received Power LED (Blue, Solid): Unit is powered on Touch Sensor Type: Capacitive touch button Location: Front panel Power Port Type: AC inlet Mains Voltage: 100 to 240 VAC, 50/60 Hz Power Consumption: 50 W typical Thermal: 170 BTU/hour typical Operating Temperature: 14 to 104°F (-10 to 40°C) ambient temperature Dimensions Without Rack-Ears: 17 x 10.73 x 1.72" (43.2 x 27.3 x 4.4 cm) With Rack-Ears: 19 x 10.73 x 1.72" (48.3 x 27.3 x 4.4 cm) Weight 9.3 lb (4.2 kg)

Description: Details iShopping.pk brings you the best price for D-Link 2 Port 100Base-TX to 100Base-FX Multi-mode Fiber (SC) Media Converter (DMC-300MSC) with express shipping all over Pakistan.   Specifications:   Number of Ports 1 x 10/100BASE-TX RJ-45 port 1 x 100BASE-FX SC port Standards IEEE 802.3 for 10BASE-T/F IEEE 802.3u for 100BASE-TX/FX Data Transfer Rate Ethernet: 10 Mbps/20 Mbps (half-duplex/full-duplex) Fast Ethernet: 100 Mbps/200 Mbps (half-duplex/full-duplex) Duplex Mode Half-duplex/full-duplex Media Types 10BASE-T: 2-pair Cat. 3/4/5/5e, Unshielded Twisted Pair (UTP) (up to 100 m) 10/100BASE-TX: 2-pair Cat. 5/5e, Unshielded Twisted Pair (UTP) (up to 100 m) 100BASE-FX: Multi-mode fi   e optic cable with SC connector (up to 2 km) Media Exchange Interface Auto-MDI/MDIX Transmission Mode Store-and-forward Forwarding Rate Full wire-speed forwarding rate Diagnostic LEDs Power Speed (for twisted pair ports) Full-duplex/Collision  LINK/ACT (for twisted pair ports) AC Input 5 V/1 A external power adapter  

Description: Details iShopping.pk brings you the best price for ClearOne Converge Pro 2 48T Audio DSP Mixer with express shipping all over Pakistan.     The CONVERGE Pro 2 48T Audio DSP Mixer from ClearOne is a complete conferencing solution with 4 mic/line inputs (AEC), 8 mic/line outputs, built-in USB audio, and built-in Telco interface for teleconferencing. It is optimized to work with Beamforming Mic Array 2 and DIALOG 20 2-Channel Wireless Microphone System through its native connection.   The mixer is suitable for use in venues such as boardrooms, conference rooms, huddle rooms, training rooms, lecture halls, courtrooms, auditoriums, and telemedicine facilities.     Features: Architecture • 4 mic/line inputs with AEC •  Built-in Telco with ClearEffect processing •  Built-in USB for PC-based conferencing Scalable Connectivity •  Standalone and daisy-chained system •  Stack up units up to 96 mic/line inputs •  Expansion bus C-Link with 64 channels •  P-Link bus to connect 6 peripherals Configuration & Management •  CONSOLE software •  Auto-discovery of devices •  Matrix View for entire system •  FlowView for visualized audio signal paths •  System monitoring and troubleshooting Audio Signal Processing •  Acoustic Echo Cancellation processing •  Distributed Echo Cancellation on every mic input •  Noise cancellation with Adaptive-Ambience •  Acoustic Intelligence with faster convergence •  DARE feedback elimination •  Microphone gating Flexible Control Options •  Dialer app for Windows, Mac, iOS, and Android •  Tabletop controller with a touch panel •  Wall controller with buttons •  Web-based controller •  Supports 3rd-party control modules     Specifications: Mic/Line Inputs Balanced audio inputs, 3.81 mm orange color Phoenix/Euroblock type male header Push-on mini-terminal block Outputs Balanced audio inputs, 3.81 mm black color Phoenix/Euroblock type male header Push-on mini-terminal block Frequency Response 20 Hz to 22 kHz @ +4 dBu, +/- 0.5 dBu EIN 20 kHz BW, max gain, Rs: 150 Ohms, -126 dBu THD + N 20 Hz to 22 kHz @ +4 dBu, line level, 0.006% 20 Hz to 22 kHz @ -56 dBu, mic level, Dynamic Range 20 Hz to 20 kHz @ 0 dB, >105 dB Crosstalk Channel to Channel Stimulus at 20 dBu to receptor at -56 dBu, 1 kHz, Input Impedance Balanced (line to ground), 2.2 kOhms, 1% Nominal Input Level Adjustable -56 dB to 0 dB, 7 dB step coarse gain Maximum Input Level -65 dBu to 20 dBu Phantom Power 48 V, Impedance: 6.81 kOhms Output Impedance Balanced (Line to Ground): 95 Ohms, 1% Output Level 0 dBu (Nominal), 20 dBu (Max), -40 dBu (Selectable) USB Audio Port Type: USB-B connector Audio: Digital audio, 2 x 2 bidirectional channels Sample Rate: 48 kHz Sample Bit Depth: 24-bit Compatible: USB 2.0, USB 3.0 Telephone Interface Port Type: RJ11   Frequency Response: Mic/Line Input to Telephone Out: 250 Hz to 3.4 kHz, +/- 2 dB, 4 dBu Telephone In to Mic/Line Out: 250 Hz to 3.4 kHz, +/- 2 dB, -15 dBu   THD + N: Mic/Line Input to Telephone Out: Telephone In to Mic/Line Out:   Dynamic Range: Mic/Line Input to Telephone Out: >67 dBu Telephone In to Mic/Line Out: >87 dBu   REN: Ringer Equivalent Number 0.2   Transhybrid Balance: 30 dB (1 kHz, all AC terminations) Ethernet Port Type: RJ-45, 10/100 Mbps Ethernet network, auto negotiation IP Address: IPv4 (IPv6 upgradeable) Amplifier Output Speaker Output Port: Dual binding posts Audio: 2 x Channel Output Power: Maximum 10 W, 8 Ohms load Frequency Response: 20 Hz to 22 kHz @ +10 dBu, +/- 0.5 dBu THD + N: 20 Hz to 22 kHz @ +10 dBu, 1 W, Dynamic Range: 20 Hz to 22 kHz @ 20 dB, >102dB, with 20 kHz digital low pass filter Crosstalk: Channel to Channel, stimulus at 20 dBu, 10 W output to receptor 8⿦ load, 20 Hz to 22 kHz, Bus C-LINK Expansion Bus Ports Type: RJ-45 (CAT5e or CAT6) C-Link In & Out: Proprietary expansion bus Audio: 64 expansion channels Cable: Solid core, factory-terminated CAT5e or 6 cable Distance: Up to 150' (45 m) Ports Type: RJ-45 (CAT5e or CAT6) P-Link In & Out: proprietary peripheral bus PoE In: P-Link in port, PoE IEEE802.3AF Audio: Up to 3 Beamforming Microphone Array 2 units + up to 3 DIALOG 20 Wireless Receiver units Cable: Solid core, factory-terminated CAT 5e or 6 cable Distance: Up to 200' (60 m) RS232 Port Type: DB9 female Settings: 9600/19200/38400/57600/115200 baud Serial echo Flow control Support: Serial commands GPIO Port Type: 5.08 mm Green color Phoenix/Euroblock type male header Support: Control, status, variable voltage control Power Pin: 5 VDC @ 350 mA power source Pin 1 to 4 Open Collector Outputs: 40 VDC @ 250 mA Active Outputs (Source/Sink): 5 VDC @ 25 mA Logic Inputs: 40.2 kOhms pull up Variable Voltage Control Inputs: 5 VDC maximum Ground Pin: GND USB Port Type: USB-B connector Location: Front panel Compatible: USB 2.0, USB 3.0 LEDs Location: Front panel Status LED (Off): Unit still initializing Status LED (Blue, Fast Blinking): Stack syncing in progress Status LED (Blue, Slow Blinking): Unit not configured Status LED (Blue, Solid): Configured unit Status LED (Red, Fast Blinking): Stack sync error Locate LED (Blue, Blinking): "Unit locate" command received Power LED (Blue, Solid): Unit is powered on Touch Sensor Type: Capacitive touch button Location: Front panel Power Port Type: AC inlet Mains Voltage: 100 to 240 VAC, 50/60 Hz Power Consumption: 50 W typical Thermal: 170 BTU/hour typical Operating Temperature: 14 to 104°F (-10 to 40°C) ambient temperature Dimensions Without Rack-Ears: 17 x 10.73 x 1.72" (43.2 x 27.3 x 4.4 cm) With Rack-Ears: 19 x 10.73 x 1.72" (48.3 x 27.3 x 4.4 cm) Weight 9.3 lb (4.2 kg)

Description: Details iShopping.pk brings you the best price for ClearOne Converge Pro 2 128T Audio DSP Mixer with express shipping all over Pakistan.   The CONVERGE Pro 2 128T Audio DSP Mixer from ClearOne is a complete conferencing solution with 12 mic/line inputs (AEC), 8 mic/line outputs, built-in USB audio, and built-in Telco interface for teleconferencing. It is optimized to work with Beamforming Mic Array 2 and DIALOG 20 2-Channel Wireless Microphone System through its native connection. The mixer is suitable for use in venues such as boardrooms, conference rooms, huddle rooms, training rooms, lecture halls, courtrooms, auditoriums, and telemedicine facilities.   Features: Architecture 12 mic/line inputs with AEC Built-in Telco with ClearEffect processing Built-in USB for PC-based conferencing Scalable Connectivity Standalone and daisy-chained system Stack up units up to 96 mic/line inputs Expansion bus C-Link with 64 channels P-Link bus to connect 6 peripherals Configuration & Management CONSOLE software Auto-discovery of devices Matrix View for entire system FlowView for visualized audio signal paths System monitoring and troubleshooting Audio Signal Processing Acoustic Echo Cancellation processing Distributed Echo Cancellation on every mic input Noise cancellation with Adaptive-Ambience Acoustic Intelligence with faster convergence DARE feedback elimination Microphone gating Flexible Control Options Dialer app for Windows, Mac, iOS, and Android Tabletop controller with a touch panel Wall controller with buttons Web-based controller Supports 3rd-party control modules   Specifications: Mic/Line Inputs Balanced audio inputs, 3.81 mm orange color Phoenix/Euroblock type male header Push-on mini-terminal block Outputs Balanced audio inputs, 3.81 mm black color Phoenix/Euroblock type male header Push-on mini-terminal block Frequency Response 20 Hz to 22 kHz @ +4 dBu, +/- 0.5 dBu EIN 20 kHz BW, max gain, Rs: 150 Ohms, -126 dBu THD + N 20 Hz to 22 kHz @ +4 dBu, line level, 0.006% 20 Hz to 22 kHz @ -56 dBu, mic level, Dynamic Range 20 Hz to 20 kHz @ 0 dB, >105 dB Crosstalk Channel to Channel Stimulus at 20 dBu to receptor at -56 dBu, 1 kHz, Input Impedance Balanced (line to ground), 2.2 kOhms, 1% Nominal Input Level Adjustable -56 dB to 0 dB, 7 dB step coarse gain Maximum Input Level -65 dBu to 20 dBu Phantom Power 48 V, Impedance: 6.81 kOhms Output Impedance Balanced (Line to Ground): 95 Ohms, 1% Output Level 0 dBu (Nominal), 20 dBu (Max), -40 dBu (Selectable) USB Audio Port Type: USB-B connector Audio: Digital audio, 2 x 2 bidirectional channels Sample Rate: 48 kHz Sample Bit Depth: 24-bit Compatible: USB 2.0, USB 3.0 Telephone Interface Port Type: RJ11   Frequency Response: Mic/Line Input to Telephone Out: 250 Hz to 3.4 kHz, +/- 2 dB, 4 dBu Telephone In to Mic/Line Out: 250 Hz to 3.4 kHz, +/- 2 dB, -15 dBu   THD + N: Mic/Line Input to Telephone Out: Telephone In to Mic/Line Out:   Dynamic Range: Mic/Line Input to Telephone Out: >67 dBu Telephone In to Mic/Line Out: >87 dBu   REN: Ringer Equivalent Number 0.2   Transhybrid Balance: 30 dB (1 kHz, all AC terminations) Ethernet Port Type: RJ-45, 10/100 Mbps Ethernet network, auto negotiation IP Address: IPv4 (IPv6 upgradeable) Bus C-LINK Expansion Bus Ports Type: RJ-45 (CAT5e or CAT6) C-Link In & Out: Proprietary expansion bus Audio: 64 expansion channels Cable: Solid core, factory-terminated CAT5e or 6 cable Distance: Up to 150' (45 m) Ports Type: RJ-45 (CAT5e or CAT6) P-Link In & Out: Proprietary peripheral bus PoE In: P-Link in port, PoE IEEE802.3AF Audio: Up to 3 Beamforming Microphone Array 2 units + up to 3 DIALOG 20 Wireless Receiver units Cable: Solid core, factory-terminated CAT 5e or 6 cable Distance: Up to 200' (60 m) RS232 Port Type: DB9 female Settings: 9600/19200/38400/57600/115200 baud Serial echo Flow control Support: Serial commands GPIO Port Type: 5.08 mm Green color Phoenix/Euroblock type male header Support: Control, status, variable voltage control Power Pin: 5 VDC @ 350 mA power source Pin 1 to 4 Open Collector Outputs: 40 VDC @ 250 mA Active Outputs (Source/Sink): 5 VDC @ 25 mA Logic Inputs: 40.2 kOhms pull up Variable Voltage Control Inputs: 5 VDC maximum Ground Pin: GND USB Port Type: USB-B connector Location: Front panel Compatible: USB 2.0, USB 3.0 LEDs Location: Front panel Status LED (Off): Unit still initializing Status LED (Blue, Fast Blinking): Stack syncing in progress Status LED (Blue, Slow Blinking): Unit not configured Status LED (Blue, Solid): Configured unit Status LED (Red, Fast Blinking): Stack sync error Locate LED (Blue, Blinking): "Unit locate" command received Power LED (Blue, Solid): Unit is powered on Touch Sensor Type: Capacitive touch button Location: Front panel Power Port Type: AC inlet Mains Voltage: 100 to 240 VAC, 50/60 Hz Power Consumption: 50 W typical Thermal: 170 BTU/hour typical Operating Temperature: 14 to 104°F (-10 to 40°C) ambient temperature Dimensions Without Rack-Ears: 17 x 10.73 x 1.72" (43.2 x 27.3 x 4.4 cm) With Rack-Ears: 19 x 10.73 x 1.72" (48.3 x 27.3 x 4.4 cm) Weight 9.3 lb (4.2 kg)

IBM Part # 42C IBM Serial # New Packed Network Adapter In Market it's Price Approximate, $. (Rs:-/ (Approx)) The NetXtreme II Express Dual Port Ethernet Adapter (marketing option part number: 42C) is a high-performance PCIe, dual-port, copper, Gigabit network adapter that supports TOE and iSCSI over a single network connection. Features and benefits: PCIe x4 PCIe 2.0-capable Two copper ports with RJ45 for Cat 5E/6 cabling Standard PCIe half-length card with low profile form factor Both half and full-height brackets to support a wide range of System x servers Support for TCP/IP Offload Engine (TOE) iSCSI-capable to allow access to storage over the same cable used for networking. Note: iSCSI support requires the purchase of a software activation key at additional cost. Software activation keys are planned to be available at a future date. The NetXtreme II Express Dual Port Ethernet adapter for System x servers delivers: Dual 1 Gigabit Ethernet ports in a PCI Express x4 adapter TOE to reduce the processing cycles required to process networking traffic in a Microsoft Windows environment Accelerated iSCSI capability to function as both a NIC and an HBA Physical specifications NetXtreme II Express Dual Port Ethernet Adapter (42C): Height: mm (4.75 in) Width: mm (4.75 in) Depth: mm (0.75 in) Operating environment Temperature: 0 to 55 (C) 32 to 131 (F) Relative humidity: 10% to 90% Agency approvals FCC part 15B Subpart J Class A CAN/CSA-C22.2 No. Canada ICES-003, Class A VCCI Class A ITE (Japan) C-Tick CE Mark CISPR 22 Class A UL CB Immunity: EN Amd + Amd Is this product Energy Star Compliant? No. Note: The Energy Star emblem does not represent EPA endorsement of any product or service. Compatibility Supported systems: IBM System x M) IBM System x M) IBM System x) IBM System x) IBM System x) IBM System x) IBM System x) IBM System x) IBM System x) IBM System x) IBM System x) IBM System x) IBM System x M) IBM System x) IBM System x M) Please see the IBM ServerProven Web page for the latest compatibility information: http://www.ibm.com/servers/eserver/serverproven/compat/us/ Box Pack - No Warranty

TP-LINK MC220L Gigabit Ethernet Media Converter Price in Pakistan MEDIA CONVERTER & MODULE Standards and Protocols IEEE 802.3ab, IEEE 802.3z, IEEE 802.3x Basic Function Full Duplex Flow Control (IEEE 802.3x) Extends fiber distance up to 0.5km for multi-mode fiber or up to 10km with single-mode fiber Ports 1 x Gigabit SFP port 1 x 10/100/1000M RJ45 port (Auto MDI/MDIX) Wave Length Depends on the used SFP module Network Media 1000BASE-X Multi-mode/Single-mode SFP module Network Media 1000BASE-T UTP category 5, 5e, 6 cable (maxium 100m) EIA/TIA-568 100O STP (maximum 100m) LED Indicators PWR, Link/Act Dimensions (W*D*H) 3.7 x 2.9 x 1.1 in. (94 x 73 x 27 mm) Power Supply External Power Adapter (9VDC/ 0.6A) Max Power Consumption 1.7 W Safety & Emission FCC, CE, RoHS Package Contents • Media Converter MC220L • Power Adapter • Installation Guide Environment Operating Temperature: 0?~40? (32?~104?) Storage Temperature: -40?~70? (-40?~158?) Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~90% non-condensing

D-Link Solid Cables Are The Best Twisted-Pair Cables In The Market For Transmitting Data Over Local Area Networks (Lans). These Cables Exceed Performance Requirements Specified By The Tia/Eia-568b.2 / Tia/Eia-568c.2 And Iec 60603-7-4 Standards. Cat6 Patch Cable 100 Mbps Speed Snagless Cable Ethernet Transmission

TP-LINK TL-R470T+ Desktop Load Balance Broadband Router Price in Pakistan HARDWARE FEATURES Standards and Protocols IEEE 802.3, 802.3u, 802.3x, TCP/IP, DHCP, ICMP, NAT, PPPoE, SNTP, HTTP, DDNS Interface 1 Fixed 10/100 Ethernet WAN Port 1 Fixed 10/100 Ethernet LAN Port 3 Changeable 10/100 Ethernet WAN/LAN Ports Network Media 10BASE-T: UTP category 3, 4, 5 cable (Max 100m) 100BASE-TX: UTP category 5, 5e cable (Max 100m) Button Reset Button Power Supply External 9V/0.6A DC Adapter Flash 16MB DRAM 128MB LED PWR, SYS, WAN, LAN, WAN/LAN Dimensions (W x D x H) 6.2 × 4.0 × 1.0 in. (158 × 101 × 25mm) PERFORMANCE Concurrent Session 10K BASIC FUNCTIONS WAN Connection Type Static/Dynamic IP, PPPoE, PPTP, L2TP, Dual Access, Bigpond Cable MAC Clone Modify WAN/LAN MAC Address DHCP DHCP Server/Client, DHCP Address Reservation Switch Setting Rate Control, Port Configuration, Port VLAN ADVANCED FUNCTIONS ACL IP/MAC/URL/WEB Filtering IGMP IGMP Proxy/IGMP Snooping Forwarding Virtual Server, Port Triggering, DMZ Load Balance Policy Routing, Link Backup Routing Static Routing Security FTP/SIP/PPTP/IPsec/H.323 ALG, DoS Defence, Ping of Death, IP/MAC Binding Traffic Control Bandwidth Control, Session Limit MANAGEMENT Service Dynamic DNS, UPnP Maintenance System Time Setting Daylight Saving Time SNMP Diagnostics Firmware Upgrade Factory Defaults/Reboot Backup/Restore System Log Remote Management System Statistics OTHERS Certification CE, FCC, RoHS Package Contents TL-R470T+ Power Adapter RJ-45 Ethernet Cable Quick Installation Guide Environment Operating Temperature: 0?~40? (32?~104?) Storage Temperature: -40?~70? (-40?~158?) Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~90% non-condensing

Linksys WAP1200AC AC1200 Wi-Fi  The  Linksys WAP1200AC AC1200 Wi-Fi Access Point  is the latest in the AC-series access points, which utilizes the  Cross Band technology.  It can be used as a  Wireless Range Extender  or a  Wired Access Point.  Both functions maximize simultaneous use of the 2.4 GHz and 5 GHz bands for high-speed data transfer, uninterrupted streaming, and gaming.   Front Panel    Antenna positioning is done depending on the type of home you have. IMPORTANT:   The antennas are fixed and can  ONLY  rotate at  180 degrees.  Do  NOT  force the antennas too far back, otherwise, they will break. For  Single-story homes  -   Both antennas should be pointing  down. NOTE:   For illustration purposes, the Linksys RE6700 is used in this example. For  Multi-story homes  -  One (1)  antenna should  always be pointing down  to provide coverage for the current floor.  The second antenna (any antenna) should be positioned differently  depending  on where the Linksys WAP1200AC is located and where the coverage is needed. NOTE:   For the most part, position one (1) antenna at  45 degrees  as shown in  Position   A  below.  If there are issues with coverage, move the antenna at about  50-55 degrees  down as shown in  Position   B.    Position A  can be used if the Linksys WAP1200AC is in the  middle  of the house.   Position B  can be used if the Linksys WAP1200AC is connected to an outlet located at the  farther side  of the house.   Side Panel    Wi-Fi Protected Setup™ (WPS)  button – Uses the WPS technology to automatically and securely add wireless devices to your network.  Reset  button – Press and hold for  10 seconds  to reset the Linksys WAP1200AC to factory default settings.   Bottom Panel    ETHERNET  port – Connect an Ethernet-enabled device to the network using either a  Cat 5  or  6  Ethernet cable.   Product Features Concurrent dual-band (2.4 GHz and 5 GHz) 802.11ac Wireless technology Compatible with 802.11 a/b/g/n Data Rate of up to 300 Mbps for 2.4 GHz and up to 867 Mbps for 5 GHz Two (2)  external non-detachable antennas 2 x 2 Spatial Streams One (1)  10/100/1000 Fast Ethernet port with auto MDIX sensing Spot Finder technology (on Range Extender Mode only) Wi-Fi Protected Setup™ (WPS) Browser-based Setup (BBS) Cross Band technology  (on Range Extender Mode only) Beamforming technology LED Behaviors  Power / WPS LED: OFF  – There is no power on the Linksys WAP1200AC. Blinking Green   / Yellow  – The Linksys WAP1200AC is starting up, resetting to factory defaults, upgrading its firmware, or the WPS connection is in process. Solid Green   / Yellow  – The Linksys WAP1200AC is ready to use. Solid Amber   / Red  – There is a weak connection with the router. NOTE:   To fix this issue, unplug the Linksys WAP1200AC and move it closer to the router. Blinking Amber / Red  – The Linksys WAP1200AC is not connected to the router, or the WPS pairing failed. NOTE:   To fix this issue, make sure that your router has an active Internet connection and the Wi-Fi is turned ON.  If the router is working fine, unplug the Linksys WAP1200AC then move it closer to the router.  Plug it back in, wait for one (1) minute, and reconnect to your network.  Ethernet LED  –   It lights up solid  Green  when an Ethernet device is connected and active.  It will blink when sending or receiving data over the Ethernet port.   Product Requirements Wi-Fi enabled computers or mobile devices AC power outlet Ethernet router or switch with available RJ45 Ethernet port and RJ45 Cable for Access Point mode or wireless network for Range Extender mode For browser configuration: Internet Explorer® 8 or higher Safari® 5.1 for Mac® or higher Google Chrome™ 25.0 or higher Firefox® 20 or higher   

Description: Details iShopping.pk brings you the best price for TP-Link 300Mbps Wireless N Access Point (TL-WA801ND) with express shipping all over Pakistan.   Features: • 300Mbps wireless speed ideal for smooth HD video, voice streaming and online gaming •  Supports multiple operation modes: Access Point, Multi-SSID, Client, Universal/WDS Repeater, Bridge with AP •  Easily setup a WPA encrypted secure connection at a push of the WPS button •  Up to 30 meters (100 feet) of flexible deployment with included Passive Power over Ethernet Injector   Specification: HARDWARE Interface One 10/100M Ethernet Port(RJ45) Support Passive PoE Button Power On/Off Button WPS Button Reset Button External Power Supply 9VDC / 0.6A Wireless Standards IEEE 802.11n, IEEE 802.11g, IEEE 802.11b Dimensions (W x D x H) 7.1 ×4.9× 1.4 in. (181 ×125 ×36mm) Antenna Type 2*5dBi Detachable Omni Directional (RP-SMA) WIRELESS Frequency 2.4-2.4835GHz Signal Rate 11n: Up to 300Mbps(dynamic) 11g: Up to 54Mbps(dynamic) 11b: Up to 11Mbps(dynamic) Reception Sensitivity 270M: -68dBm@10% PER 130M: -68dBm@10% PER 108M: -68dBm@10% PER 54M: -68dBm@10% PER 11M: -85dBm@8% PER 6M: -88dBm@10% PER 1M: -90dBm@8% PER Transmit Power Wireless Modes AP Mode Multi-SSID Mode Client Mode Repeater Mode (WDS/Universal) Bridge with AP Mode Wireless Functions Enable/Disable Wireless Radio WDS Bridge MAC Address Filter Wireless Security 64/128/152-bit WEP / WPA / WPA2,WPA-PSK / WPA2-PSK Quality of Service WMM Management SNMP Advanced Functions Up to 30 meters Passive PoE is supported OTHERS Certification CE, FCC, RoHS System Requirements Microsoft Windows 98SE, NT, 2000, XP, Vista™ or Windows 7, MAC OS, NetWare, UNIX or Linux. Environment Operating Temperature: 0℃~40℃ (32℉~104℉) Storage Temperature: -40℃~70℃ (-40℉~158℉) Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~90% non-condensing   What This Product Does The TP-LINK Wireless N Access Point TL-WA801ND is designed to establish or expand a scalable high-speed wireless N network or to connect multiple Ethernet enabled devices such as game consoles, digital media adapters, printers, or network attached storage devices to a wireless network. The APs support a host of different functions that makes your wireless networking experience more flexible than ever before. Now, you can enjoy a better Internet experience when downloading, gaming, video streaming or with any other application that you may wish to use.   Wireless N - Speed & Range Adopting IEEE 802.11n advanced MIMO (Multi Input Multi Output) technology, it simultaneously works through two antennas to Tx and Rx to overcome the interference and signal degradation when traveling long distances or through physical barriers in a small office or a large apartment, resulting in an incredible improvement in the wireless performance, even in a steel-and-concrete building. Above all, you could easily pick up the wireless network during long-distance connection where legacy 11g products may not!   Multiple Operating Modes  - Easy to Build WLAN Supports multiple operation modes (Access Point, Multi-SSID, Client, Universal/ WDS Repeater, Bridge with AP) to enable various wireless applications to give users a more dynamic and comprehensive experience when using their AP. Multiple operating mode also helps you easily to build wireless network for hard-to-wire locations or eliminating wireless dead zone.   Passive PoE Supported  - More Flexible Deployment The TL-WA801ND is able to be powered using an Ethernet cable to simultaneously send data and electricity to wherever your AP may be located even up to 100 feet away. This feature multiplies your options allowing you to place the AP in a position that is most convenient to get the best signal possible, such as on the wall or on the ceiling of your office.

TP-Link 300Mbps Wireless N Access Point TL-WA801N Price in Pakistan HARDWARE FEATURES Interface: 1× 10/100 M Ethernet Port(RJ45) Support Passive PoE Button: Power On/O? Button, WPS Button, Reset Button External Power Supply: 9VDC / 0.6A Wireless Standards: IEEE 802.11n, IEEE 802.11g, IEEE 802.11b Dimensions (W x D x H): 7.1 × 5.1 × 1.4 in (181.6 × 129.5 × 36.2 mm) Antenna Type: 2 Fixed Omni-Directional Antennas WIRELESS FEATURES Frequency: 2.4 GHz Signal Rate: 300 Mbps at 2.4 GHz Reception Sensitivity: 11g 6Mbps: -90dBm 11g 54Mbps: -77dBm 11n HT20 MC7: -73dBm 11n HT40 MC7: -70dBm Transmit Power: CE: Wireless Modes: AP Mode Multi-SSID Mode Client Mode Range Extender Mode Wireless Functions: Enable/Disable Wireless Radio, WMM, Short GI, AP Isolation, Wireless Statistics, Throughput Monitor Wireless Security: WEP, WPA/WPA2, WPA/WPA2-PSK encryptions Quality of Service: WMM Management: SNMP Advanced Functions: Up to 30 meters Passive PoE is supported OTHERS Certification: CE, FCC, RoHS Package Contents: Wireless Access Point TL-WA801N Power Adapter Passive PoE Power Injector RJ45 Ethernet Cable Quick Installation Guide System Requirements: Microsoft Windows 98SE/NT/2000/XP/Vista™/7/8/8.1/10, MAC OS, NetWare, UNIX or Linux Internet Explorer 11, Firefox 12.0, Chrome 20.0, Safari 4.0, or other Java-enabled browser Cable or DSL Modem Subscription with an Internet Service Provider (for Internet access) Environment: Operating Temperature: 0°C~40°C (32°F ~104°F) Storage Temperature: -40°C~70°C (-40°F ~158°F) Operating Humidity: 10%~90% RH Storage Humidity: 5%~90% RH

Description: Details iShopping.pk brings you the best price for D-Link 6-Port 10/100 Unmanaged PoE Switch (DES-F1006P-E) with express shipping all over Pakistan.   Details: Long-Distance Transmission with Surge Protection With a connectivity range of 250 meters, the DES-F1006P-E is ideal for surveillance deployments, and compatible with Cat.5e or Cat.6 copper cable, while 6kV surge protection helps this device withstand power fluctuations and lightning strikes.   Easy Deployment and PoE Convenience The DES-F1006P-E is a Plug-and-Play device that requires no configuration, so setup is simple and hassle-free. Easily connect multiple computers, share files, music, and video across your SOHO network, or even create a multiplayer gaming environment. 802.3x flow control on each port minimizes dropped packets when the port’s receiving buffer is full, giving a more reliable connection for all connected devices. The DES-F1006P-E also features four 10/100BASE-TX ports that support the IEEE 802.3af/at Power-over-Ethernet (PoE) protocol, supplying 15W each.   Diverse Operating Modes The DES-F1006P-E switch has three operating modes. The default mode has a transmission distance of 100 meters. VLAN mode prevents against DHCP deception, broadcast storms, and virus attacks. Extend mode supports an extra-long transmission distance of 250 meters at 10Mbps, and Quality-of-Service (QoS) mode customizes application priorities for uses such as Video.   Features: • 4 x 10/100 Mbps Fast Ethernet Ports •   2 x 10/100 Mbps Uplink Port •   Power-over-Ethernet (60W) •   Flow control for protection against data loss •   Maximum distance of 250m •   QoS Capabilities •   Surge protection (6kV) •   Operating Temperature: 0 to 40oC