ELECTROMAGNETIC PARKING SENSOR, EASY INSTALLATION, NO DIRL IN PAKISTAN

Improves parking safety. Detection in all directions without dead angle. Minimize bumper damage. Totally built-in installation without impair overall appearance. Indicates object distance with different beeping frequencies. The sensor antenna activates 3 types of acoustic signals during approaching an obstacle at different distances. A continuous sound of Beep approximately between 0-0.3m A short interval sound of Beep approximately between m A long interval sound of Beep approximately between m Simple and concealed installation. The sensor antenna is entirely installed inside the bumper without any drilling work. Maintenance free, no cleaning or washing is required. Fit for any car, truck, RV or mini-van. Peel & Stick Antenna foil tape sensor for vehicles bumpers. Wires to Reverse Lamp (12 Volts DC) High output Piezo buzzer alert you with a beeping sound Detects object at 3 feet or less PD1 Rear parking sensor provides your car with full rear bumper protection when parking and reversing, alerting you to approaching objects via an audible speaker. When reverse gear is engaged the PD1 Rear parking sensor provides an instant, automatic, self-diagnostic function that maps out the surrounding area of your rear bumper constantly monitoring this as you reverse with 100% accuracy, providing you with 3 different audible tones (Zones) alerting you of your proximity in relation to surrounding objects! The full length of your bumper (including the sides) is protected with an ever increasing beeping sound. As you reverse, Zone 1 (furthest away from your vehicle) detects the approaching object first. Zone 1: 80 to 50 cm in length - The 1st tone signals with a slow "be-be-be" sound Zone 2: 50 to 25 cm in length - The 2nd tone is a faster "be-be-be" sound Zone 3: 25cm and less - the 3rd tone is a constant "beeeeeep" sound Installation: The Universal Parking Dynamics PD1 is compatible with any Car, Vehicle, Van, 4x4, MPV, SUV and Motor home that has a plastic bumper and as 99.9% of cars and vehicles have plastic bumpers, you have no need to be concerned, even if your bumper appears part metal the PD1 will work. If you are in any doubt please contact us. The PD1 antenna is easy to fit and requires no bumper adjustments or holes ensuring a damage free installation. The antenna is cost effective to replace should you wish to move the sensor to a new car in the future or simply require a replacement. Mounting the Electronic Control Unit (ECU): The Rear ECU can be installed in various locations such as inside of the boot behind the trim or inside your rear bumper with the included adhesive mount. The Front ECU can be installed inside of the engine bay or behind the glove box, dashboard or trim with the included adhesive mount. Mounting the Speaker: Mount the parking sensor speaker using the included adhesive mount. The volume is loud enough to provide a good warning even if mounted behind your vehicles interior trim. This connects to the ECU by push fit connection. Can be extended up to 15M and will mount in any location. Mounting the Antenna: Mount the adhesive metallic parking sensor antenna onto the inner side of the front and/or rear bumper (depending upon which sensor option you choose) making sure the bumper surface is clean before attaching. Ensure the terminal connector is on the side where you have located the ECU. When the antenna has been attached, covering the whole of the bumper from left to right (leaving approx 15cm from the edges); the excess length is cut off. Place a piece of the included adhesive material or tape at either end of the antenna to ensure a secure installation onto the bumper. Its recommended (but not essential) to cover antenna length with a black anti-rust protection paint that is applied to the underneath of a car chassis or similar to protect from the elements. It is important that the antenna is installed at the highest part from the ground that corresponds to the furthest distance from the vehicle body as a precaution to prevent any interference from nearby metal parts. The recommended position of the parking sensor antenna is at least 40cm from ground level, with 50cm being optimum. Once the bumper is removed, if your vehicle has a metal crash protection bar and the antenna will be within 3 cm's of this metal bar (once the bumper is re-fitted) you can install a 2nd Antenna (included with all PD1 sensors) to prevent any reduction in detection range or insulate the metal crash bar. Courier TO Any CIty Avalable Box Pack - No Warranty