Simulator rc planes flying

This Simulator Adapter can be used with any make of radio, even one with no trainer port and can be used as either a wireless or hard-wire Simulator Adapter. It can be used with any make of radio when used in conjunction with a reciever or can it be used with standard 3.5mm Jack Lead (supplied), supports XTR, Aerofly, FMS, Phoenix 3.0, 4.0, Realflight G3, G4, G5. *Note: This is the update version with micro USB connector. Includes: Wireless/Hardwired Adapter USB Cable 3.5mm Jack Lead Male/Male Receiver to Adapter Leads Instructions Views: 3

With v2 firmware update, correcting many flaws of the previous 9X, plus inbuilt 2.4Ghz (no daggy second antenna) this is a quality, reliable 2.4Ghz system suitable for beginners and pro pilots alike. Get that locked-in feeling that only 2.4Ghz glitch free technology can provide. Ultra fast reaction times and interference free control of your model is only achievable with this 2.4Ghz technology. Without a doubt, the best value 9Ch system available! Number of Channnel: 8ch ppm/9ch pcm Display: 128*64LCD Support Type: Heli/Acro/Glid Support user: 8 Stick model: 4 Encoder type: ppm/pcm Subtrim: Yes Simulator Interface: Yes Buzzer: Yes Low Voltage Show: Yes Required: Battery Included: Turnigy 9x 9Ch Transmitter Turnigy RF9X-V2 module Turnigy 9X8C-V2 8-channel receiver

J.X.F props are well balanced and made of reinforced plastic, making them strong and very well formed. New! Never mounted on motors. 4 pieces are available 200Rs each Discount: 80Rs if u buy all four pieces. Tags: RC Planes Helicopter Quadcopter Multicopter Flying Hobby Hobbyist Remote Control Pusher Puller Box Pack - No Warranty

The CC3D EVO provides a crisp feel when flying tricopters, quads, hexas, octocopters, and even fixed wing planes. CC3D EVO CopterControl Hardware Features WIth a function of being directly plugged into the satellite receiver(It needn't conversion cable) Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM. 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer. Tiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight performance. Software support for Windows, for mac and Linux. Direct high speed USB support with no drivers required, a truly plug and play device. for spektrum satellite receiver support. Futaba S-BUS hardware support. Innovative Flexi-port technology for superior port flexibility. 4Mbits on-board EEPROM for configuration storage. Flexiport CopterControl also offers the innovative Flexi-port which provides either I2C connectivity or a second serial port. Flexi-port gives CopterControl the flexibility to use either I2C and a single serial port or dual serial ports, according to your connectivity needs. Superior user experience OpenPilot has tried to make your experience with the CC3D as easy and trouble-free as possible. Naturally for a high-end product, the hardware is complete; there is nothing to solder. The included RC harness allows you to connect any standard PWM receiver. All CopterControl boards are tested before shipping and come with bootloader already flashed. A standard mini-USB cable (not included) is used to load the latest firmware and configure everything for your unique airframe. The OpenPilot project, whist still young, it trying to make Open Source much more user friendly. OpenPilot software is designed to be used by everybody! All major operating systems are supported and install packages are provided. The software is all Free software under the GPLv3 license and not only are you welcome to hack it, but we encourage it! Sensors and Components 3-axis Gupports several common RC inputs: 6 PWM channels, combined PPM, for spektrum/JR DSM2, Supports several common RC inputs: 6 PWM channels, combined PPM, for spektrum/JR DSM2, DSMJ, for satellites, and Futaba S.Bus receivers. Simultaneous support for multiple receivers. ReceiverPort functions (configurable): 6 PWM input channels or combined PPM stream, 4 PWM output channels MainPort functions (configurable): serial telemetry (default), GPS, S.Bus, for spektrum/JR satellites FlexiPort (configurable): serial telemetry, GPS, for spektrum/JR satellites, or I2C peripherals (under development) 10 PWM outputs to servos or ESC’s, or for camera stabilization Camera stabilization: supports up to 3-axis camera mounts with stabilization and manual control from any of configured receivers. Onboard USB connectivity for easy configuration. USB and serial telemetry and configuration Supported by powerful OpenPilot GCS 4 Mbit onboard memory 3C Quaternion based complementary filter running at 500Hz Package included: 1 PC CC3D EVO flight controller 1 PC plastic shell 1 set wires Views: 5

The CC3D EVO provides a crisp feel when flying tricopters, quads, hexas, octocopters, and even fixed wing planes. CC3D EVO CopterControl Hardware Features WIth a function of being directly plugged into the satellite receiver(It needn't conversion cable) Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and 20KB RAM. 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer. Tiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight performance. Software support for Windows, for mac and Linux. Direct high speed USB support with no drivers required, a truly plug and play device. for spektrum satellite receiver support. Futaba S-BUS hardware support. Innovative Flexi-port technology for superior port flexibility. 4Mbits on-board EEPROM for configuration storage. Flexiport CopterControl also offers the innovative Flexi-port which provides either I2C connectivity or a second serial port. Flexi-port gives CopterControl the flexibility to use either I2C and a single serial port or dual serial ports, according to your connectivity needs. Superior user experience OpenPilot has tried to make your experience with the CC3D as easy and trouble-free as possible. Naturally for a high-end product, the hardware is complete; there is nothing to solder. The included RC harness allows you to connect any standard PWM receiver. All CopterControl boards are tested before shipping and come with bootloader already flashed. A standard mini-USB cable (not included) is used to load the latest firmware and configure everything for your unique airframe. The OpenPilot project, whist still young, it trying to make Open Source much more user friendly. OpenPilot software is designed to be used by everybody! All major operating systems are supported and install packages are provided. The software is all Free software under the GPLv3 license and not only are you welcome to hack it, but we encourage it! Sensors and Components 3-axis Gupports several common RC inputs: 6 PWM channels, combined PPM, for spektrum/JR DSM2, Supports several common RC inputs: 6 PWM channels, combined PPM, for spektrum/JR DSM2, DSMJ, for satellites, and Futaba S.Bus receivers. Simultaneous support for multiple receivers. ReceiverPort functions (configurable): 6 PWM input channels or combined PPM stream, 4 PWM output channels MainPort functions (configurable): serial telemetry (default), GPS, S.Bus, for spektrum/JR satellites FlexiPort (configurable): serial telemetry, GPS, for spektrum/JR satellites, or I2C peripherals (under development) 10 PWM outputs to servos or ESC’s, or for camera stabilization Camera stabilization: supports up to 3-axis camera mounts with stabilization and manual control from any of configured receivers. Onboard USB connectivity for easy configuration. USB and serial telemetry and configuration Supported by powerful OpenPilot GCS 4 Mbit onboard memory 3C Quaternion based complementary filter running at 500Hz Package included: 1 PC CC3D EVO flight controller 1 PC plastic shell 1 set wires Views: 213