Hydrogen gas

Many countries are now using this on demand Oxy hydrogen gas system to save up to 30% fuel or up to 50% incrteased Km in one kg gas or one liter patrol.Normally the fuel does not burn completely in cumbustion and this wastage is about 30%. The gas produced by water electrolysis is directed through intake to combustion chamber.It burns completely the patrol or CNG and improve engine power.We Note down Km Avg/kg gas or /liter patrol before and after HHO dry cell installation.100% guaranty of increased km,Clean engine from carbon, increase engine life.see the test result report of HHO car running in hyderabad for last two months.The car has completed 10000 km with HHO gas.study these sites for hho gas advantages.http://tophhogascar.com/hho-dry-cell-kits-advantages/ , http://www.hho2u.com/HHO_DRY_CELL.html , http://auto-hydrogen.com/what-is-hho/why-use-hydrogen , watch video of vehicle (kiya sportage 2000 cc) having HHO system, https://www.facebook.com/savingsolution/videos/1109243765830073/ , Video of Toyota GLI 2011 https://www.facebook.com/savingsolution/videos/1108318882589228/

first owner fresh car honda city 1.3ivtec manual pumper to pumper jeniun car.(android panel install.low mileage untouch spare whell throughout hydrogen gas on wheel interior just like new with new car fragrance excellent condition just buy and drive. Only serious buyer can contact avoid brokers.thanks Mention PakWheels.com when calling Seller to get a good deal 2018 33,000Petrol Manual

STIRLING ENGINE SPECIFICATIONS: Power = 1/20hp (37 Watts) Hot air compression & Stirling Cycle Engine Design Air cooled - no water required If properly configured can generate power 1 Kg. Gas can run for Hours Consumes 2 BTU Flame without load and 5 BTU with load Light weight & portable (gas tank, not included) Can use Natural Gas, CNG, LPG, Propane, Oils, Hydrogen, Biogas, Solar Built-in Natural Gas Jet (Replace jet for LPG) Built-in Holder for carriage Turns on with a finger push No grease or engine oil required Very minimal use of fire flame Included Fly wheel Size = 7" (Seven Inch) Fly wheel Surface Speed 500m/min (Average) Speed = 1,800 RPM (No Load) if properly settled Engine Size = 58cc (Measurements not Power) Piston = 50mm (No rings, uncompressed, depressurized) Rust-Free combination of metals Discharges thermal heat Best for the student experiments, off-grid living or remote area Very Low Noise - smooth operation Weight: Approx. 15 Kg. (without gas tank) Dimensions: Height 27" x Width 14" x Length 14"

Laser Welding System 180 Watt The multi-purpose laser welding system (also called as laser mould welder, mould repair) is specially designed for the mould industry and used in repairing of precision moulds, such as mould manufacture for digital products, mobile phone, toy, automobile and motorcycle, and moulding industry. Through the repairing of moulds, it is possible to reuse the moulds, save the production cost and improve the working efficiency significantly. This technology can also be used to modify the design or size of moulds to reduce the development period. Features The working principle of this laser deposition welding system is to use laser high thermal energy and the melting technology in spot to process the welding and repairing of minute parts. It makes up the shortage of traditional hydrogen arc welding in repairing precision surfaces, avoids the two difficulties of thermal strain and after-treatment, and saves the production period of mould. Advantages It is specially designed for the mould industry and the technology is imported from Germany. With unique structure design, it is suitable for repairing of large, medium and small moulds. 1. Ceramic converging cavity is imported from the Britain. It is corrosion resistant and high temperature resistant, and has 8-10 years service life. The life of xenon lamp is more than 8 million times. 2. Use the most advanced light shielding system to eliminate the irritation to eyes by light during working. 3. The laser head and optics part can be rotated for 360°, upward/downward lifting and forward/backward pushing, suitable for repairing of large, medium and small moulds. 4. The parameters are controlled by intelligent remote controller, which is simple and convenient. 5. The work bench can be lifted, and moved in three dimensions, the size of light spot can be adjusted. Suitable materials The materials that can be welded are extensive: cold work alloy steel, hot work alloy steel, nickel tool steel, high grade steel, steel alloy, high tenacity aluminum alloy, etc. Technical data Model ZEE-180 3-axis stroke of work bench X=300mm, Y=200mm (X, Y can be adjusted manually and Z-axis can be manually motorized to lift maximum 250mm.) Bearing of work bench ≤200kg Device weight 300kg Power supply 220V±10%/50Hz or 380V±10%/50Hz Laser parameters Laser parameters Laser type Nd:YAG pulse Adjusting range of light spot 0.1-0.3mm Size of light spot 0.2-3.0mm Laser wavelength 1064nm Pulse width ≤20ms Maximum laser power 180W/200W Pulse frequency ≤15Hz Laser output focus length 50mm/100mm/120mm (optional) Laser cooling Water cooling Observing system Microscope (360° adjustable) Protection gas One line (xenon) Welding wire diameter 0.1mm-0.6mm USD19800