Motor driver
Top sales list motor driver
Pakistan
Input voltage 6V-27V Maximum Current 43A Input level 3.3V-5V Control mode PWM or horizontal Size 5cm x 5cm x 1.2cm2.0 x 2.0 x 0.5inch LWH The drive uses a full H-bridge driver module Infineon chip BTS7960 composed of high-power drive, with overheating overcurrent protection. Pair BTS7960 H-bridge driver circuit, with a strong drive and braking effect, effectively isolate the microcontroller and motor driver Features 1.double BTS7960 high current 43A H-bridge driver. 2.and MCU 5V isolation, effective protection of the microcontroller. 3.enables the motor forward reverse, two-way 25kHZ highest frequency PWM input. 4..two passing streams overheat error signal output. 5.isolation chip 5V power supply 5V can be shared with the microcontroller. 6.Power supply voltage 5.5V to 27V. This product is suitable for driving coreless motor, general motor, thermoelectric cooling module, solenoid valves, solenoid coils. Package Included 1 pcs as the picture shows
Rs 1,5
See product
Pakistan
L298 Motor Driver Controller Board The L298N driver module, using ST L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface , you can chip circuitry to 5V power supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential. Stepper Motor Driver L298 CONTROLLER BOARD Now Buy Online Shipping All Across Pakistan COMPANY: MATRIX ELECTRONICS CONTACT PERSON: FAIZAN MUNIR Mobile:0 3002785860 w w w .matrixelectronic . com Email : sales @ matrixelectronic . com Email : info @ matrixelectronic . com
Free
See product
Pakistan (All cities)
L293D Motor DriverThis L293D motor driver is a 4-channel driver with an Arduino shield form factor. This is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepper motors. It lets you drive 2 Stepper motor or 4 DC motors with an Arduino, controlling the speed and direction of each one independently.Features:2 interface for 5V Servo Can drive 4 DC motors or 2 stepper motors or 2 Servo Up to 4 bi-directional DC motors with individual 8-bit speed selection Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping. 4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 36V DC Pull down resistors keep motors disabled during power-up Reset button 2 external terminal power interface, for separate logic/motor supplies
Rs 399
See product
Pakistan
Manufacturer Part Number L293D Description IC MOTOR DRIVER PAR 16-DIP Lead Free Status RoHS Status Lead free RoHS Compliant Standard Package 25 Category Integrated Circuits ICs Family PMIC - Motor Drivers, Controllers Series - Motor Type - Stepper Bipolar Motor Type - AC, DC Brushed DC Function Driver - Fully Integrated, Control and Power Stage Output Configuration Half Bridge 4 Interface Parallel Technology - Step Resolution - Applications General Purpose Current - Output 600mA Voltage - Supply 4.5 V 36 V Voltage - Load 4.5 V 36 V Operating Temperature -40C 150C TJ Mounting Type Through Hole Package Case 16-DIP 0.300, 7.62mm Supplier Device Package 16-PowerDIP Online Catalog Drivers
Rs 80
See product
Lahore (Punjab)
This dual bidirectional motor driver is based on the very popular L298 Dual H-Bridge Motor Driver Integrated Circuit. The circuit will allow you to easily and independently control two motors of up to 2A each in both directions. It is ideal for robotic applications and well suited for connection to a microcontroller requiring just a couple of control lines per motor. For more details and products and projects call/msg
Rs 3.000
See product
Pakistan
Overview Dual stepper motor driver shield can drive 2 stepper motors at the same time by Arduino. It can work with the power supply from 4.75V to 30V. High accuracy controlling can be supported by Arduino for CNC milling machine. It uses the same stepper motor driver chip as EasyDriver, so you can use it as 2 EasyDriver modules on board. And there are all pins breakout as 3PIN electronic brick/ sensor brick interface. " Box Pack - No Warranty
Rs 2.500
See product
Pakistan
Overview Dual stepper motor driver shield can drive 2 stepper motors at the same time by Arduino. It can work with the power supply from 4.75V to 30V. High accuracy controlling can be supported by Arduino for CNC milling machine. It uses the same stepper motor driver chip as EasyDriver, so you can use it as 2 EasyDriver modules on board. And there are all pins breakout as 3PIN electronic brick/ sensor brick interface. " Facebook page;ElectronicsArena.com Box Pack - No Warranty
Rs 2.500
See product
Peshawar (Khyber Pakhtunkhwa)
Overview Dual stepper motor driver shield can drive 2 stepper motors at the same time by Arduino. It can work with the power supply from 4.75V to 30V. High accuracy controlling can be supported by Arduino for CNC milling machine. It uses the same stepper motor driver chip as EasyDriver, so you can use it as 2 EasyDriver modules on board. And there are all pins breakout as 3PIN electronic brick/ sensor brick interface. " Facebook page;ElectronicsArena.com
Rs 2.500
See product
Pakistan
overview dual stepper motor driver shield can drive 2 stepper motors at the same time by arduino. it can work with the power supply from 4.75v to 30v. high accuracy controlling can be supported by arduino for cnc milling machine. it uses the same stepper motor driver chip as easydriver, so you can use it as 2 easydriver modules on board. and there are all pins breakout as 3pin electronic brick sensor brick interface. " Box Pack - No Warranty
Rs 2,5
See product
Pakistan
ULN Stepper Motor Driver Board is to use the ULN DARLINGTON ARRAYS to drive the 4-phase 5-wire stepper motor (5v-12v). It's easy to use Arduino or other development platform to drive the stepper motor by this diver board. Box Pack - No Warranty
Rs 200
See product
Pakistan
ULN Stepper Motor Driver Board is to use the ULN DARLINGTON ARRAYS to drive the 4-phase 5-wire stepper motor (5v-12v). It's easy to use Arduino or other development platform to drive the stepper motor by this diver board. Facebook page;ElectronicsArena.com Box Pack - No Warranty
Rs 200
See product
Peshawar (Khyber Pakhtunkhwa)
ULN Stepper Motor Driver Board is to use the ULN DARLINGTON ARRAYS to drive the 4-phase 5-wire stepper motor (5v-12v). It's easy to use Arduino or other development platform to drive the stepper motor by this diver board. Facebook page;ElectronicsArena.com
Rs 200
See product
Pakistan
uln 003 stepper motor driver board is to use the uln darling ton arrays to drive the 4 phase 5 wire stepper motor 5v 12v. it s easy to use arduino or other development platform to drive the stepper motor by this diver board. Box Pack - No Warranty
Rs 200
See product
Pakistan
ULN Stepper Motor Driver Board is to use the ULN DARLINGTON ARRAYS to drive the 4-phase 5-wire stepper motor 5v-12v. Its easy to use Arduino or other development platform to drive the stepper motor by this diver board. Box Pack - No Warranty
Rs 200
See product
Pakistan
EASYDRIVER - STEPPER MOTOR DRIVER Now Buy Online Shipping All Across Pakistan COMPANY: MATRIX ELECTRONICS CONTACT PERSON: FAIZAN MUNIR Mobile:03002785860 www.matrixelectronic.com Email : sales@matrixelectronic.com Email : info@matrixelectronic.com Founded In 2003: We Deal In All Kinds Of Electronic Components, Test And Measuring Instruments, Variety Of Multimeters, Toolkits, Hand Tools, Universal IC Progammers, Etc Matrix Online Store Dedicated To Electronics Engineers, Hobbyists and Students. Visit www.matrixelectronic.com Address: Shop#2, Hassan Centre Near Passport Office Saddar karachi.
Free
See product
Pakistan
Description The LN298 is a high voltage, high current, dual full-bridge motor driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Comes in a staggered, 15-lead Multiwatt package. Check below for a breakout board. Features Operating supply voltage of up to 46V 4.5-7VDC logic supply voltage Total DC current of up to 4A Low saturation voltage Over-temperature protection Logical 0 input up to 1.5V high-noise immunity
Rs 150
See product
Pakistan
Features: Double H bridge drive Chip L298N (ST NEW) Logical voltage 5V Drive voltage 5V-35V Logic current 0mA-36mA Drive current 2A(MAX single bridge) Storage temperature -20 to +135 Max power 25W Weight 30g Small size mm (approx 1.75"" x 1.75"" x 1"") Compatible with L297/L298 driver Note This module has a built-in 5v power supply for external use. Drive voltage is 7v-35v. DO NOT input voltage to +5v supply interface - this is OUTPUT only." Box Pack - No Warranty
Rs 450
See product
Pakistan
Features Double H bridge drive Chip L298N ST NEW Logical voltage 5V Drive voltage 5V-35V Logic current 0mA-36mA Drive current 2AMAX single bridge Storage temperature -20 to 135 Max power 25W Weight 30g Small size 434327mm approx 1.75 x 1.75 x 1 Compatible with L297L298 driver Note This module has a built-in 5v power supply for external use. Drive voltage is 7v-35v. DO NOT input voltage to 5v supply interface - this is OUTPUT only.
Rs 450
See product
Pakistan (All cities)
1. supply voltage DC24-80V or AC18-50V2. Drive current 2.4-7.2A3. Subdivision accuracy 2-200 subdivision optional4. Optically isolated signal input
Rs 4.998
See product
Lahore (Punjab)
Toshiba TBAHQ chip - High power, maximum 3.5A drive current. · Professional design, two-stage signal processing, super anti-jamming. · microstep setting - Higher accuracy. · Adjustable drive current settings for each axis - % of full current can be set for different stepper motors. · Overload, over-current and over-temperature safety - Full protection for your computer and peripheral equipment. · On board current switching - Power output can be set according to specific user requirement. · Relay spindle interface - Outputs Max. 36V 7.5A for spindle motors or coolant pump (only one device can be powered by this output!) · 4 channel inputs interface- Can be used for XYZ limit and emergency stop. · Bipolar constant current chopper drive with non-resonant region. · Full closed-type optical isolation to protect the user's computer and equipment · Four control inputs (divided into pairs of knives) - Allows setting of limit and emergency stop. · Universal architecture - Supports most parallel software MACH3,KCAM4,EMC2 etc.
Rs 4.500
See product
Pakistan
RTL-09896 SparkFun Now Buy Online Shipping All Across Pakistan COMPANY: MATRIX ELECTRONICS CONTACT PERSON: FAIZAN MUNIR Mobile:03002785860 www.matrixelectronic.com Email : sales@matrixelectronic.com Email : info@matrixelectronic.com Founded In 2003: We Deal In All Kinds Of Electronic Components, Test And Measuring Instruments, Variety Of Multimeters, Toolkits, Hand Tools, Universal IC Progammers, Etc Matrix Online Store Dedicated To Electronics Engineers, Hobbyists and Students. Visit www.matrixelectronic.com Address: Shop#2, Hassan Centre Near Passport Office Saddar karachi.
Free
See product
Pakistan
Input voltage 6V-27V Maximum Current 43A Input level 3.3V-5V Control mode PWM or horizontal Size 5cm x 5cm x 1.2cm2.0 x 2.0 x 0.5inch LWH
See product
Pakistan (All cities)
Simple step and direction control interface Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step Can interface directly with 3.3 V and 5 V systems Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout Short-to-ground and shorted-load protection 4-layer, 2 oz copper PCB for improved heat dissipation Exposed solderable ground pad below the driver IC on the bottom of the PCB Module size, pinout, and interface match those of our A4988 stepper motor driver carriers in most respects (see the bottom of this page for more information) Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay) 45 V maximum supply voltage Built-in regulator (no external logic voltage supply needed)
Rs 249
See product
Pakistan (All cities)
Dual H-bridge motor driver module Operating mode H-bridge driver (dual) Master chip L298N Logic voltage 5V Drive voltage 5V-35V
Rs 449
See product
Safdar Abad (Punjab)
1. Driver: L298N Dual H Bridge DC Motor Driver IC 2. driven part of the terminal supply area Vs: 5 V ~ 35 V; such as the need to take power within the board, the supply area Vs: 7V ~ 35V 3. driven part of the peak current Io: 2A 4. the logical part of the terminal supply area Vss: 5 V ~ 7 V (can take power within the board 5 V) 5. the logical part of the operating current range: 0 ~ 36mA 6. control signal input voltage range: Low:-0.3V Box Pack - No Warranty
Rs 1.300
See product
Pakistan
Maximum current rating: 30A • Maximum voltage: 41V • MOSFET on-resistance: 19mOhm (per leg) • Maximum PWM frequency: 20kHz • Undervoltage and overvoltage shutdown The Monster Motor Controller Shield For Arduino (14A, V) is essentially a ramped up version of Sparkfun's Ardumoto motor driver shield. For this monster shield maufacturer has replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. Manufacturer has also beefed up the support circuitry so this board is capable of driving a pair of high-current motors. Box Pack - No Warranty
Rs 3.500
See product
Pakistan
Maximum current rating: 30A Maximum voltage: 41V MOSFET on-resistance: 19mOhm Maximum PWM frequency: 20kHz Undervoltage and overvoltage shutdown The Monster Motor Controller Shield For Arduino 14A, V is essentially a ramped up version of Sparkfun's Ardumoto motor driver shield. For this monster shield maufacturer has replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. Manufacturer has also beefed up the support circuitry so this board is capable of driving a pair of high-current motors." Facebook page;ElectronicsArena.com Box Pack - No Warranty
Rs 3.500
See product
Peshawar (Khyber Pakhtunkhwa)
Maximum current rating: 30A Maximum voltage: 41V MOSFET on-resistance: 19mOhm Maximum PWM frequency: 20kHz Undervoltage and overvoltage shutdown The Monster Motor Controller Shield For Arduino 14A, V is essentially a ramped up version of Sparkfun's Ardumoto motor driver shield. For this monster shield maufacturer has replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. Manufacturer has also beefed up the support circuitry so this board is capable of driving a pair of high-current motors." Facebook page;ElectronicsArena.com
Rs 3.500
See product
Pakistan
Maximum current rating: 30A Maximum voltage: 41V MOSFET on-resistance: 19mOhm Maximum PWM frequency: 20kHz Undervoltage and overvoltage shutdown The Monster Motor Controller Shield For Arduino 14A, V is essentially a ramped up version of Sparkfun's Ardumoto motor driver shield. For this monster shield maufacturer has replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. Manufacturer has also beefed up the support circuitry so this board is capable of driving a pair of high-current motors." Box Pack - No Warranty
Rs 3.500
See product
Pakistan
Maximum current rating: 30A Maximum voltage: 41V MOSFET on-resistance: 19mOhm Maximum PWM frequency: 20kHz Undervoltage and overvoltage shutdown The Monster Motor Controller Shield For Arduino 14A, V is essentially a ramped up version of Sparkfun's Ardumoto motor driver shield. For this monster shield maufacturer has replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. Manufacturer has also beefed up the support circuitry so this board is capable of driving a pair of high-current motors."
Rs 3.500
See product
-
Next →
Visit our blog
Share on Facebook
Share on Twitter