Controller board bent

L298 Motor Driver Controller Board The L298N driver module, using ST L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface, you can chip circuitry to 5V power supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential. Stepper Motor Driver L298 CONTROLLER BOARD Now Buy Online Shipping All Across Pakistan COMPANY MATRIX ELECTRONICS CONTACT PERSON FAIZAN MUNIR Mobile0 w w w.matrixelectronic. com Email sales matrixelectronic. com Email info matrixelectronic. com Box Pack

APM V2.8.0 Flight Controller Upgrade Verstion 2.6 2.5.2 for Multirotor Fixed Wing APM V2.8.0 description: – This version eliminates the 1.0mm 6P SM06B GPS interface of V2.52 old version, and change it into DF13-4P I2C external compass interface. – Put DF13-5P GPS interface with external compass interface, convenient for the connection of GPS and externalcompass. – V2.52 I2C interface changes to multifunctional MUX interface – Modified version added isolation resistor, when the OSD interface used with telemetry, the interfaces is effectively avoided – V2.52 version 3.5V power supply adopts IPS79133, 6V withstand voltage, output current 100mA, need to supply power for six IC, slightly inadequate power supply ability, easy to be burnt dwon. The new version adopts US LP2985-3.3, 16V withstand voltage, more reliable, redcucing the possibility of Bad Gyro health APM V2.8.0 Flight Controller – Needle: staight – Power supply: LP2985-3.3 – Max voltage: 16V – Add a 47uF tantalum capacitor – Port: MUX (UART0, UART2, mnnI2 and OSD are optional, OSD is the defaulted output) Jumper cap choose: – Built-in compass: plug the jumper cap in the MAG pin header. – External compass: pull up the jumper cap from the MAG pin header. Package Included: – 1pcs APM2.8 Flight Controller Board with shell – 1pcs shock absorber – 1pcs power module – 1pcs 7M / M8N GPS – 1pcs GPS holder Views: 3

APM V2.8.0 Flight Controller Upgrade Verstion 2.6 2.5.2 for Multirotor Fixed Wing APM V2.8.0 description: – This version eliminates the 1.0mm 6P SM06B GPS interface of V2.52 old version, and change it into DF13-4P I2C external compass interface. – Put DF13-5P GPS interface with external compass interface, convenient for the connection of GPS and externalcompass. – V2.52 I2C interface changes to multifunctional MUX interface – Modified version added isolation resistor, when the OSD interface used with telemetry, the interfaces is effectively avoided – V2.52 version 3.5V power supply adopts IPS79133, 6V withstand voltage, output current 100mA, need to supply power for six IC, slightly inadequate power supply ability, easy to be burnt dwon. The new version adopts US LP2985-3.3, 16V withstand voltage, more reliable, redcucing the possibility of Bad Gyro health APM V2.8.0 Flight Controller – Needle: staight – Power supply: LP2985-3.3 – Max voltage: 16V – Add a 47uF tantalum capacitor – Port: MUX (UART0, UART2, mnnI2 and OSD are optional, OSD is the defaulted output) Jumper cap choose: – Built-in compass: plug the jumper cap in the MAG pin header. – External compass: pull up the jumper cap from the MAG pin header. Package Included: – 1pcs APM2.8 Flight Controller Board with shell – 1pcs shock absorber – 1pcs power module – 1pcs 7M / M8N GPS – 1pcs GPS holder Views: 1

APM2.8 ArduPilot Mega 2.8 APM Flight Controller Board with Ublox NEO M8N GPS w/ Built-in Compass + Power Module XT60 Plug Soldered for RC Multicopter Arduino Compatible. – Can be ordered with top entry pins for attaching connectors vertically, or as side entry pins to slide your connectors into either end horizontally – Includes 3-axis gyro, accelerometer and magnetometer, along with a high-performance barometer – Onboard 4 MegaByte Dataflash chip for automatic data logging – Optional off-board GPS, uBlox LEA-6H module with Compass. – One of the first open source autopilot systems to use Invensense’s 6 DoF Accelerometer/Gyro MPU-6000. – Barometric pressure sensor upgraded to MS5611-01BA03, from Measurement Specialties. – Atmel’s ATMEGA2560 and ATMEGA32U-2 chips for processing and USB functions respectively. Other similar RC products are also available on our website with delivery to any city in Pakistan. Visit our website for updated price and pictures. Views: 3

The KK2 is next big evolution of the first generation KK flight control boards. The KK2 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts. The LCD screen and built-in software make install and setup easier than ever. A host of multi-rotor craft types are pre-installed, simply select your craft type, check motor layout/propeller direction, calibrate your ESCs and radio and you’re ready to go! All of which is done with easy to follow on screen prompts! The original KK gyro system has been updated to an incredibly sensitive 6050 MPU system making this the most stable KK board ever and allowing for the addition of an auto-level function. At the heart of the KK2 is an Atmel Mega644PA 8-bit AVR RISC-based microcontroller with 64k of memory. An additional polarity protected header has been added for voltage detection, so no need for onboard soldering. A handy piezo buzzer is also included for audio warning when activating and deactivating the board. The KK2 added polarity protection to the voltage sense header and a fuse protected buzzer outputs, in case something is accidentally plugged in incorrectly. The voltage sense line has been updated for better accuracy. The board is clearly labelled and the voltage sense line colour has been changed to red for easy identification, making installation and connections a snap. If you’re new to multi-rotor flight or have been unsure about how to setup a KK board then the KK2 was built for you. The 6 Pin USBasp AVR programming interface ensures future software updates will be quick and easy. Specifications: Size: 50.5mm x 50.5mm x 12mm Weight: 21 gram (Include Piezo buzzer) IC: Atmega644 PA Gyro/Acc: 6050MPU InvenSense Inc. Auto-level: Yes Input Voltage: 4.8-6.0V AVR interface: standard 6 pin. Signal from Receiver: 1520us (5 channels) Signal to ESC: 1520us Firmware Version: 1.6+ Built-in aeroplane mode: Dualcopter Tricopter Y6 Quadcopter + Quadcopter X Hexacopter + Hexacopter X Octocopter + Octocopter X X8 + X8 X H8 H6 V8 V6 Aero 1S Aileron Aero 2S Aileron Flying Wing Singlecopter 2M 2S Singlecopter 1M 4S Views: 3

The KK2 is next big evolution of the first generation KK flight control boards. The KK2 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts. The LCD screen and built-in software make install and setup easier than ever. A host of multi-rotor craft types are pre-installed, simply select your craft type, check motor layout/propeller direction, calibrate your ESCs and radio and you’re ready to go! All of which is done with easy to follow on screen prompts! The original KK gyro system has been updated to an incredibly sensitive 6050 MPU system making this the most stable KK board ever and allowing for the addition of an auto-level function. At the heart of the KK2 is an Atmel Mega644PA 8-bit AVR RISC-based microcontroller with 64k of memory. An additional polarity protected header has been added for voltage detection, so no need for onboard soldering. A handy piezo buzzer is also included for audio warning when activating and deactivating the board. The KK2 added polarity protection to the voltage sense header and a fuse protected buzzer outputs, in case something is accidentally plugged in incorrectly. The voltage sense line has been updated for better accuracy. The board is clearly labelled and the voltage sense line colour has been changed to red for easy identification, making installation and connections a snap. If you’re new to multi-rotor flight or have been unsure about how to setup a KK board then the KK2 was built for you. The 6 Pin USBasp AVR programming interface ensures future software updates will be quick and easy. Specifications: Size: 50.5mm x 50.5mm x 12mm Weight: 21 gram (Include Piezo buzzer) IC: Atmega644 PA Gyro/Acc: 6050MPU InvenSense Inc. Auto-level: Yes Input Voltage: 4.8-6.0V AVR interface: standard 6 pin. Signal from Receiver: 1520us (5 channels) Signal to ESC: 1520us Firmware Version: 1.6+ Built-in aeroplane mode: Dualcopter Tricopter Y6 Quadcopter + Quadcopter X Hexacopter + Hexacopter X Octocopter + Octocopter X X8 + X8 X H8 H6 V8 V6 Aero 1S Aileron Aero 2S Aileron Flying Wing Singlecopter 2M 2S Singlecopter 1M 4S Views: 1

Specification   This is the new APM 2.8 autopilot module. The sensors are exactly the same as with APM2.6, however this version does not have an onboard compass, which makes this version ideal for use with multicopters and rovers.     The APM 2.8 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition. It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints. Available with top or side connectors.     This revision of the board has no onboard compass, which is designed for vehicles (especially multicopters and rovers) where the compass should be placed as far from power and motor sources as possible to avoid magnetic interference. (On fixed wing aircraft it's often easier to mount APM far enough away from the motors and ESCs to avoid magnetic interference, so this is not as critical, but APM 2.6 gives more flexibility in that positioning and is a good choice for them, too). This is designed to be used with the 3DR uBlox GPS with Compass (see option below), so that the GPS/Compass unit can be mounted further from noise sources than APM itself.     Arduino Compatible!     Can be ordered with top entry pins for attaching connectors vertically, or as side entry pins to slide your connectors in to either end horizontally     Includes 3-axis gyro, accelerometer and magnetometer, along with a high-performance barometer     Onboard 4 MegaByte Dataflash chip for automatic datalogging     Optional off-board GPS, uBlox LEA-6H module with Compass.     One of the first open source autopilot systems to use Invensense's 6 DoF Accelerometer/Gyro MPU-6000.     Barometric pressure sensor upgraded to MS5611-01BA03, from Measurement Specialties.     Atmel's ATMEGA2560 and ATMEGA32U-2 chips for processing and usb functions respectively.

Key FeaturesThe L298 Stepper Controller makes it easy to drive either two DC motors or a bipolar stepper motor. Double H bridge driveChip L298N (ST NEW)Logical voltage 5VDrive voltage 5V-35VLogic current 0mA-36mADrive current 2A(MAX single bridge)Storage temperature -20 to +135Max power 25W Small size mm (approx 1.75" x 1.75" x 1")Compatible with L297/L298 driver Specifications Material Dimensions (cm) Weight (kg) Mixed Material 4.3 x 4.3 x

Brand: Accessories & Gadgets Price: 500 Seller Type: An Individual Condition: New Arduino Shield: Dual H Bridge DC Stepper Motor Drive Controller Board Module L298N. Best and most inexpensive way to drive DC Stepper Motors with microcontrollers especially with the Arduino boards.

MinimOSD Mini OSD Board On Screen Display Video Record for Mavlink Support APM APM 2.5 2.6 RC Flight Controller FPV APM has an inexpensive companion OSD board called MinimOSD. It reads all the MAVLink data in the APM telemetry stream and overlays it on the video stream if youre using an on-board camera and wireless video transmitter FAIZAN MUNIR Mobile0 3002785860 Email sales matrixelectronic. com w w w.matrixelectronic. com

LED WRITING/FLASH BOARD WITH HANGER/STAND, ERASER, MARKERS AND REMOTE CONTROL. Advantages: Advertise your Business with "LED FLASH BOARD" Catch Customer Attention Offer your Sales when needed Change your Offer when needed Flexible, Rewritable,Cost effective Ideal tool to boost your business WHO Can have LED FLASH/WRITING BOARD ? Hotels,Schools,Wedding Halls, Shopping Malls, Restaurants, Bars, Cafes, Shops,Retail stores, Supermarkets Nightclubs Multinational Companies, Showrooms, Offices. Package Contents: 1x Led Writing Board 1x Power Adaptor 1x 24 Key IR Controller (Free) 8x Color Pens 1x Wiping Cloth 1x Hanging Chain 1x Stand - ePlugins Shop G-22, TM Plaza D.A.V. College Road Rawalpindi facebook/ePlugins -

EZION TOUCH SCREEN AND REMOTE SWITCH CONTROLLER: Size: 86*146mm usually call 3*6 Max Current: 10A each switch. Max Voltage: 200 volt each switch. 50-60 Hz 110-220 volt. 4 lights & 1 fan with regulator (1-9 levels for fan dimmer) Complete touch screen display with remote control operated. Full function remote control & touch screen. Memory system installed... Installation is very simple and same like normal switch board. WARRANTEE: Warrantee only for technical fault, no warrantee broken and if open. BOX CONTAIN: 1 x Switch Board 1 x Remote Control Views: 3

Specifications: – Size: Approx. 96 x 61 x 34mm/3.78 x 2.40 x 1.34” – Input Voltage Range: DC6V-60V – Output Voltage: Linear with load – Output Current: 0A-30A – Continuous Current: 20A – Speed Range: 0% to 100% – Regulation Method: Potentiometer – Regulation Type: Regulating Current – Control Frequency: 15KHz – Wiring Type: Screw terminal Features: – Speed controller is made with high quality circuit board which ensures a longer service life. – This simple and easy-to-use DC motor speed controller has an stable performance. – Designed with a digital display that shows the rate in percentage of actual speed to maximum speed. – This motor speed controller uses screw terminals for convenient and quick wiring. – Comes with a momentary start/stop switch and a speed control potentiometer. Package Included: – 1 x Speed Controller Like our Page Electronics Panga Views: 2

Features: Working voltage DC 10V-35V. Recommended using a switching power supply DC24V power supply. 6N137 high-speed optical coupling, guarantee high speed without losing the step. Using the TB6560AHQ chip with low voltage shutdown, overheating stop and over current protection circuit to ensure optimal performance. Rated maximum output: ± 3A, peak 3.5A. For two-phase within 42,57 stepping 3A / four-phase / of line four / six-wire stepper motor, and is not suitable for more than 3A stepper motor. Automatic half current function. Subdivision: whole step, half-step, step 1/8, 1/16 step, a maximum of 16 subdivisions. Specifications: Working voltage: DC 10-35V Rated maximum output: ± 3A, peak 3.5A. Main colour: Green Size:75 x 50 x 33mm Net weight: 83g Package content: 1x TB6560 3A driver board Working voltage: DC 10-35V Rated maximum output: ± 3A, peak 3.5A. Main color: Green Size:75 x 50 x 33mm Net weight:83g Package content: 1x TB6560 3A driver board Views: 1

Universal LCD LED TV Board Remote with 30 Pin LVDS Grip Kit 3663 Digital DVB-C DVB-T2 Universal LCD TV Controller Driver Board TV Kit